RIDGID TS3660 manual To Store Accessories, To Install Front and Back Rails, Square Head Bolt

Page 22

ASSEMBLY

TO STORE ACCESSORIES

See Figure 19.

The table saw has two convenient storage areas (one on either side of the saw cabinet) specifically designed for the saw’s accessories.

When not in use, store the accessories securely by snapping each accessory in place.

TO INSTALL FRONT AND BACK RAILS

See Figures 20 - 22.

To Install Front Rail:

Insert square head bolts (5/16-18 x 1 in.) into the holes on the front of the saw table and extension tables.

Attach flanged hex nut (5/16-18) loosely allowing the square bolt head to protrude.

Slide the front rail slot over each of the square head bolts and finger tighten the nuts.

Align the front rail with the 7-1/8 in. mark on the right side rip scale with the right edge of the cast iron table top.

To Install Back Rail:

Insert square head bolts (5/16-18 x 1 in.) into the holes on the back of the saw table and extension tables.

Attach flanged hex nut (5/16-18) loosely allowing the square bolt head to protrude.

Slide the back rail slot over each of the square head bolts and finger tighten the four nuts.

Place a framing square on either side of the blade. Move the back rail right or left until the indicator mark is aligned with the framing square. Finger tighten the nuts.

TOOL STORAGE

Fig. 19

SQUARE

HEAD

BOLT

	FLANGED
FRONT	HEX NUT
FRONT	(5/16-18)
RAIL

Fig. 20

SQUARE HEAD

BOLT

(5/16-18 x 1 in.)

FLANGED
HEX NUT
(5/16-18)	REAR
	EXTENSION
	RAIL
	Fig. 21
RIGHT EDGE OF
TABLE TOP

Fig. 22

22

Image 22

Contents OPERATOR’S Manual Table of Contents IntroductionGeneral Safety Rules Read ALL Instructions Blade Coasts After Being Turned OFF Specific Safety Rules Before Making a CUT, be Sure ALL ADJUST- Ments are Secure  Never Operate the SAW on the FloorSpecific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Authorized Service Center for repair. When servicExtension Cords Speed and WiringElectrical Electrical ConnectionChanging Motor Voltage See Figures 2Motor Thermal Overload Protector Junction BOX Manual Reset ButtonSee Figure Glossary of Terms RIP Fence FeaturesProduct Specifications Bevel ScaleKnow Your Table SAW OverviewHEX Keys 4 2.5 mm, 1/8 in., 5/32 in., 3/16 Tools NeededSquare Framing Square Loose Parts Key Description QtyLoose Parts List Unpacking AssemblyMounting Holes To Assemble LEG Stand and Storage Brackets To Mount the Table SAW to the LEG Stand To Install Extension TablesScrew With Washer To Install the HERC-U-LIFT Mobile Base to the LEG Stand Lock Blade Tube Height Lock Knob Adjusting Handwheel To Install Bevel Adjusting HAND- WheelTo Install Height Adjusting HAND- Wheel To assemble the Herc-U-Lift to the leg standTool Storage Square Head Bolt To Store AccessoriesTo Install Front and Back Rails Square Head BoltSee Figures 23 To Adjust Front and Back RailsFront Rail Rear Shims SET Screws RIP Fence in Locked Position Unlocked Position To Install RIP FenceTo Check the Throat Plate See Figures 27To Install Blade Guard Assembly To Install Spacer BARTo Align Blade Guard Assembly to the Blade To Install Belt To Mount Motor AssemblyTo Install the Belt Guard Motor AssemblyTo Install END Caps To Install Switch AssemblyTo Secure the Electrical Cords To Adjust Blade Depth To Adjust Blade AngleOperation Push Sticks Push Blocks HOW to Make a FeatherboardFeatherboard See Figures 41Cutting Tips Types of CutsCross CUT To USE the HERC-U-LIFT Mobile Base to Move the Table SAW To USE the IND-I-CUT FeatureUnlock Pedal Metal Platform To USE the SAW Dust Chute To USE the MICRO-ADJUST Feature on the RIP FenceMICRO-ADJUST Wheel Dust Chute See Figures 46To Make a Cross CUT Switch KEY Removed Switch onSee Figures 49 To Make a RIP CUT To Make a Miter CUTViewed from the FRONT, below the Table SAW To Make a Bevel Cross CUTTo Make a Bevel RIP CUT To TightenBevel RIP CUT Blade Angled To Make a Compound Bevel Miter CUTScale RIP Fence To Make a Large Panel CUT To Make a NON-THROUGH CUT NON-THROUGH CUTTo Make a Dado CUT Dado CUTTo REMOVE/REPLACE the Throat Plate AdjustmentsTo Install Zero Clearance Throat Plate Removing Throat Plate Zero ClearanceSee Figures 62 To Replace the SAW BladeBlade Wrench Washer NUT Framing Square Trunnion Bolt Heeling Paralleling the Blade to the Miter Gauge GrooveSee Figures 64 Trunnion Bolt LeverSee Figures 67 To SET the Bevel Indicator and Bevel Stops AT 0˚ and 45˚Screws Bevel Lock Lever Blade AT 90˚ Position To Adjust the Bevel Adjusting HAND- Wheel To Adjust the Miter GaugeLocking Lever HEX Head Screws Adjusting NUT Back Rail To Align and Adjust the RIP FenceSee Figures 74 To Adjust the RIP Fence Indicator PAN Head ScrewGeneral Maintenance MaintenanceAccessories LubricationTroubleshooting Problem CauseSolution What is Covered Under the 3 Year Limited Service Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not CoveredCustomer Service Information Model No TS3660 Serial No