RIDGID TS3660 To Install Bevel Adjusting HAND- Wheel, To Install Height Adjusting HAND- Wheel

Page 21

ASSEMBLY

To assemble the Herc-U-Lift™ to the leg stand:

Install the four leg brackets on the inside of each leg using head screws (1/4-20 x 1/2 in.) and lock nuts (1/4-20). Tighten securely.

Place the lower section under the leg stand with the ends of the tube under the front leg brackets. Place a screw with washer (1/4-20 x 1-5/8) through the leg bracket and the end of the tube of the lower section. Secure in place using lock nuts (1/4-20).

NOTE: The screw should freely pivot.

Repeat above step for the upper section of the Herc-U- Lift™.

Check to insure the upper and lower sections are centered. If required, loosen frame hardware and adjust the frames side to side to center. Retighten all hardware.

Press down on the unlock pedal to check alignment of the U-bolt. The U-bolt should be centered within the latch mechanism as shown in figure 16. Release the unlock pedal and adjust the U-bolt as necessary. Retighten all hardware.

NOTE: With the tool on a level surface, check to make sure the tool does not move. If tool moves, adjust all four leveling feet supporting the tool.

TO INSTALL BEVEL ADJUSTING HAND- WHEEL

See Figure 17.

Locate the following parts:

1 bevel handwheel

1 pan head screw (1/4-20 x 5/8 in. with washer)

Push bevel handwheel onto the bevel shaft aligning flats on the bevel shaft with the flats on the bevel handwheel.

Secure in place using the screw (1/4-20 x 5/8 in. with washer).

TO INSTALL HEIGHT ADJUSTING HAND- WHEEL

See Figure 18.

Remove blade height lock knob by turning the knob counterclockwise.

Slide the height adjusting handwheel onto the rod and against the lock tube.

Secure the height adjustment handwheel by reinstalling the blade height lock knob.

UNLOCK

PEDAL

LATCHU-BOLT

MECHANISM

CENTER U-BOLT WITHIN THE LATCH MECHANISM

Fig. 16

BEVEL

ADJUSTING

HANDWHEEL

PAN HEAD SCREW

(1/4-20 x 5/8 in.)

Fig. 17

LOCK

BLADE TUBE

HEIGHT

LOCK KNOB

HEIGHT

ADJUSTING

HANDWHEEL

Fig. 18

21

Image 21

Contents OPERATOR’S Manual Introduction Table of ContentsRead ALL Instructions General Safety Rules Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Specific Safety Rules Blade Coasts After Being Turned OFF  Never Operate the SAW on the FloorSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsAuthorized Service Center for repair. When servic ServiceElectrical Speed and WiringExtension Cords Electrical ConnectionSee Figures 2 Changing Motor VoltageJunction BOX Manual Reset Button Motor Thermal Overload ProtectorSee Figure Glossary of Terms Product Specifications FeaturesRIP Fence Bevel ScaleOverview Know Your Table SAWTools Needed HEX Keys 4 2.5 mm, 1/8 in., 5/32 in., 3/16Square Framing Square Key Description Qty Loose PartsLoose Parts List Assembly UnpackingMounting Holes To Assemble LEG Stand and Storage Brackets To Install Extension Tables To Mount the Table SAW to the LEG StandScrew With Washer To Install the HERC-U-LIFT Mobile Base to the LEG Stand To Install Height Adjusting HAND- Wheel To Install Bevel Adjusting HAND- WheelLock Blade Tube Height Lock Knob Adjusting Handwheel To assemble the Herc-U-Lift to the leg standTo Install Front and Back Rails To Store AccessoriesTool Storage Square Head Bolt Square Head BoltTo Adjust Front and Back Rails See Figures 23Front Rail Rear Shims To Check the Throat Plate To Install RIP FenceSET Screws RIP Fence in Locked Position Unlocked Position See Figures 27To Install Spacer BAR To Install Blade Guard AssemblyTo Align Blade Guard Assembly to the Blade To Install the Belt Guard To Mount Motor AssemblyTo Install Belt Motor AssemblyTo Install Switch Assembly To Install END CapsTo Secure the Electrical Cords To Adjust Blade Angle To Adjust Blade DepthOperation Featherboard HOW to Make a FeatherboardPush Sticks Push Blocks See Figures 41Types of Cuts Cutting TipsCross CUT To USE the IND-I-CUT Feature To USE the HERC-U-LIFT Mobile Base to Move the Table SAWUnlock Pedal Metal Platform MICRO-ADJUST Wheel Dust Chute To USE the MICRO-ADJUST Feature on the RIP FenceTo USE the SAW Dust Chute See Figures 46Switch KEY Removed Switch on To Make a Cross CUTSee Figures 49 To Make a Miter CUT To Make a RIP CUTTo Make a Bevel RIP CUT To Make a Bevel Cross CUTViewed from the FRONT, below the Table SAW To TightenTo Make a Compound Bevel Miter CUT Bevel RIP CUT Blade AngledScale RIP Fence To Make a Large Panel CUT NON-THROUGH CUT To Make a NON-THROUGH CUTDado CUT To Make a Dado CUTTo Install Zero Clearance Throat Plate AdjustmentsTo REMOVE/REPLACE the Throat Plate Removing Throat Plate Zero ClearanceTo Replace the SAW Blade See Figures 62Blade Wrench Washer NUT Framing Square See Figures 64 Heeling Paralleling the Blade to the Miter Gauge GrooveTrunnion Bolt Trunnion Bolt LeverTo SET the Bevel Indicator and Bevel Stops AT 0˚ and 45˚ See Figures 67Screws Bevel Lock Lever Blade AT 90˚ Position To Adjust the Miter Gauge To Adjust the Bevel Adjusting HAND- WheelTo Align and Adjust the RIP Fence Locking Lever HEX Head Screws Adjusting NUT Back RailSee Figures 74 PAN Head Screw To Adjust the RIP Fence IndicatorAccessories MaintenanceGeneral Maintenance LubricationProblem Cause TroubleshootingSolution DAY Satisfaction Guarantee Policy WarrantyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredModel No TS3660 Serial No Customer Service Information