Simrad SIMRAD HS50 manual Cable, Interface, Processing unit to sensor unit cable

Page 16

Simrad HS50 Heading Sensor

Processing unit

Enclosure material:

Anodized aluminum

Enclosure protection:

IP44

Operating temperature range:

0 to +55ºC (32 to 131°F)

Storage temperature range:

-20 to +60ºC (-4 to 140°F)

Safe distance to compass:

0.2 m (0.7 ft)

2.8 Cable

 

Processing unit to sensor unit cable

Type:

2x2x0.5 mm2 with shield

Maximum length:

100 m (328 ft)

Diameter:

10 mm (0.4 in.)

Flame retardation:

IEC 332-3/A

2.9 Interface

Configuration:

Display unit connected to the Processing unit

Data outputs:

Three RS-232 serial lines,

 

Three RS-422 serial lines,

 

 

Ethernet UDP/IP

Data inputs:

One RS-232 and one RS-422 serial line

DGPS corrections:

RTCM 104 version 2.2 and SAPOS® EPS

Baud rate:

Max. 38.4 kBaud

HDT, ROT, GGA and GLL data update rates:

.......... Up to 20 Hz

HDT, ROT, GGA and GLL data delay:

Less than 50 ms

ZDA and VTG data update rate:

Max 1 Hz

VTG data delay:

Max 1.5 sec

ZDA data delay:

1 ms

Data output formats:

NMEA 0183 ZDA, GGA, GLL, VTG, HDT, ROT, GSA, GRS and proprietary messages PSXN,20. The PSXN,20 message include position, height and heading quality information

RD Instrument ADCP proprietary NMEA format, "PRDID".

Radar clock data

8

20221081 / F

Image 16
Contents Simrad HS50 Heading Sensor Copyright 20221081 / F Document revisions Contents Operating Instructions Figures and Drawings This page Intentially Left Blank Introduction HS50 System components20221081 / F Definitions, abbreviations and acronyms About this manualDefinitions Abbreviations and acronyms NmeaRestrictions in guarantee Health, environment and safetyRestrictions in use Physical dimensions Performance dataSensor unit Display unitEnvironmental specification PowerProcessing unit Interface CableProcessing unit to sensor unit cable Cable connection GeneralGrounding Sensor unit Location of the unitMechanical installation Bracket mounting option Cable wiring Pedestal mounting optionWaterproofing the connectors Display unitPanel mounting Alternative panel mountingBracket mounting option Display unit cable Processing unit Cable connections Display Unit Sensor Unit RGC Signal Interface unit Connecting to Simrad equipmentAP9MK3 Autopilot NI300X J50/J300X Junction unitIS15 Instruments RGC12 Gyro Compass Simrad RA40/RA50 RadarSoftware setup procedure Display Adjustments ExampleDifferential corrections Data output All six serial lines may be used simultaneouslyEthernet GeneralHeight aiding Velocity filteringRadar format DatumExpert setup HDT-QRun mode Heading offsetExample Operating Instructions OverviewTurning the system ON/OFF Performance monitoring348 Navigation/HDT display Navigation/POS displayInfo displays Hdop PdopGps hdt Deviation Accuracy Last heading Common sat Alarms Invalid Heading alarm Invalid Position alarmInvalid Position and Heading alarm Operation Height aided GPS positionThis page Intentially Left Blank Maintenance Periodic maintenanceSoftware upgrades Re-calibration of the Sensor unitTroubleshooting Repairs and modificationsReplacing damaged cables Replacing damaged unitsNo response No valid dataNo Differential corrections Invalid HeadingReduced heading indication Simulated dataFigures and Drawings Dimensions SeatexSensor unit bracket, dimensions Kongsberg SeatexSensor unit Processing unit, dimensions Display unit, dimensions Optional equipment Standard deliveryDocumentation