Sterling 882.01749.00 manual Screw Recovery Times Screen Injection only, Manual Run / Jog Screen

Page 48

Displays the current motor speed when running, and the calculated speed when stopped.

Screw Recovery Times Screen (Injection only)

Displays the 5 most recent screw recovery times (latest on top), as well as the simple average and weighted average.

Manual Run / Jog Screen

This screen is only available when the A250 control is stopped. This screen provides the means to purge / clear additive, prime additive, etc..

The speed at which the motor will run, jog, or purge. Adjust using the Accel and Decel buttons.

Pressing and holding either of these buttons will adjust the motor run speed by approximately 1% of max speed every ½ second. The minimum speed is 5%, while the maximum speed is 100%. The default speed is 50%.

882.01749.00

48 of 93

Image 48

Contents Digital Dosing Disc Additive Feeders Write Down Your Serial Numbers Here For Future Reference Shipping Info Unpacking and InspectionTable of Contents Appendix a Basic Parameter Settings Safety How to Use This ManualGeneral Safety Regulations ResponsibilityOperate this equipment within design specifications Functional Description IntroductionA250 Controller Duo Dual Station Digital Dosing FeederQuick Start-Up Guide UnpackingFeeder Configuration Injection Molding Motor and alarm utilty selection Encoder PulsesPage Injection molding Additive %Shot Size Screw Recovery Time Calibration weightDD Pellet Discs DT Pellet & Regrind Discs DP Powder DiscsDisc Additive Sample weighingRPM Page Recipe Setup for Simple Extrusion Throughput Feeder Configuration Extrusion follower 8400 Bodine Motor and alarm utilty selection Recipe Setup for Simple Extrusion Throughput Speed Weight Calibration Disc Calibration Number ThicknessScreen Screen Screen Installation and Operation Installation882.01749.00 TB #51 TB #54 Initial Operation Recipes Recipe MenuEnter / Edit Recipes Screw Recovery Time Simple Extrusion Recipe Extrusion Follower Recipe Throughput Speed Calibration Screen Screen Status screens PrerequisitesCommon Elements Buttons Speed Status Indicator Disc Motor IndicatorPress Signal Indicator Totalizer Screen Throughput ScreenMotor Speed Screen Screw Recovery Times Screen Injection only Manual Run / Jog ScreenConfiguration Navigation System Setup MenuSystem Setup Navigation Buttons 882.01749.00 882.01749.00 Feeder Type Encoder Pulses Maximum Motor SpeedManufacturer Motor Color Black & silver Drive Tuning Speed AlarmDefault Additive Measure Default Shot Size / Throughput Measure Injection Press Additive / Virgin Material Sensor Press Signal Type. Extrusion Follower only Minimum Press Signal. Extrusion Follower onlyMaximum Press Signal. Extrusion Follower only Passwords Screen Digital I/O Monitor Optional Features Level switches probesAnalog / Encoder Monitor Level Sensor Adjustment Screw Communication Protocol Interfaces Optional Additive Hoppers882.01749.00 Virgin Material Supply Hoppers Maintenance Preventative Maintenance IntervalsDD Dosing Module Pellets Installing the shear Removing the Shear Plate DD dosing ModuleRemoving the shear Removing the DD Disc and Cleaning the Dosing Module Dismantling the Dosing ModuleInstalling the Dosing Module Installing Different Types of Dosing DiscsDT Dosing Module Pellets and Some Regrind Removing/Replacing the Wiper in the DT Dosing Station Removing the DT Disc and cleaning the dosing station DP Powder Dosing Module Removing/Replacing the DT Disc & Cleaning the Dosing Station Removing the DP Disc and Cleaning the Dosing Station Exchangeable Dosing Modules DD DiscsDT Discs DP DiscsSpare Parts DD Dosing Units QTY DescriptionDT Dosing Units QTY DescriptionDP Dosing Units QTY DescriptionDD/DT/DP Additional Spare PartsAppendix a Basic Parameter Settings Recipe FormulasAppendix B Disc Sizing Guides DiscDisc Min/Max Appendix C Drawings Single Station Digital Dosing FeederDuo Digital Dosing Feeder Electrical Schematics of A250 Controller 882.01749.00 Appendix D Spare Parts List Replacement Motor Assembly Part NumbersDosing Disc/Shear Order Numbers Appendix E Technical Assistance Sterling, Inc882.01749.00