Sterling 882.01749.00 manual Removing the DT Disc and cleaning the dosing station

Page 75

4-5 Removing the “DT” Disc and cleaning the dosing station

1.Switch the control unit “Off” with the “On/Off” switch.

2.Disconnect the power supply.

3.Open the toggle latches.

2.Remove the dosing hopper (D) from the motor.

3.Empty the dosing station.

4.Open the profile clamp (C).

6.Remove the profile clamp (C).

7.Remove the dosing hopper assembly (A and B).

6.Remove the two M6 x 30 socket screws (B) on top of the dosing disc (A).

7.Lift the dosing disc (A) from the dosing unit housing.

8.Clean the components with a cotton cloth.

9.Clean the dosing hopper (A and B) in soapy water.

10.Dry all parts thoroughly.

11.Install the dosing hopper on the dosing module (locating the guide pin).

12.Install the profile clamp and tighten the screw.

13.Mount the dosing housing onto the dosing motor.

14.Close the toggle latches, securing the dosing module to the motor assembly.

882.01749.00

75 of 93

Image 75
Contents Digital Dosing Disc Additive Feeders Write Down Your Serial Numbers Here For Future Reference Unpacking and Inspection Shipping InfoTable of Contents Appendix a Basic Parameter Settings How to Use This Manual SafetyResponsibility General Safety RegulationsOperate this equipment within design specifications Introduction Functional DescriptionDuo Dual Station Digital Dosing Feeder A250 ControllerUnpacking Quick Start-Up GuideFeeder Configuration Injection Molding Encoder Pulses Motor and alarm utilty selectionPage Injection molding Additive %Shot Size Screw Recovery Time Calibration weightDD Pellet Discs Additive Sample weighing DT Pellet & Regrind DiscsDP Powder Discs DiscRPM Page Recipe Setup for Simple Extrusion Throughput Feeder Configuration Extrusion follower 8400 Bodine Motor and alarm utilty selection Recipe Setup for Simple Extrusion Throughput Speed Disc Calibration Number Thickness Weight CalibrationScreen Screen Screen Installation Installation and Operation882.01749.00 TB #51 TB #54 Initial Operation Recipe Menu RecipesEnter / Edit Recipes Screw Recovery Time Simple Extrusion Recipe Extrusion Follower Recipe Throughput Speed Calibration Screen Screen Prerequisites Status screensCommon Elements Buttons Speed Status Indicator Disc Motor IndicatorPress Signal Indicator Totalizer Screen Throughput ScreenMotor Speed Screen Manual Run / Jog Screen Screw Recovery Times Screen Injection onlySystem Setup Menu Configuration NavigationSystem Setup Navigation Buttons 882.01749.00 882.01749.00 Feeder Type Encoder Pulses Maximum Motor SpeedManufacturer Motor Color Black & silver Speed Alarm Drive TuningDefault Additive Measure Default Shot Size / Throughput Measure Injection Press Additive / Virgin Material Sensor Press Signal Type. Extrusion Follower only Minimum Press Signal. Extrusion Follower onlyMaximum Press Signal. Extrusion Follower only Passwords Screen Digital I/O Monitor Optional Features Level switches probesAnalog / Encoder Monitor Level Sensor Adjustment Screw Optional Additive Hoppers Communication Protocol Interfaces882.01749.00 Virgin Material Supply Hoppers Preventative Maintenance Intervals MaintenanceDD Dosing Module Pellets Installing the shear Removing the Shear Plate DD dosing ModuleRemoving the shear Dismantling the Dosing Module Removing the DD Disc and Cleaning the Dosing ModuleInstalling Different Types of Dosing Discs Installing the Dosing ModuleDT Dosing Module Pellets and Some Regrind Removing/Replacing the Wiper in the DT Dosing Station Removing the DT Disc and cleaning the dosing station DP Powder Dosing Module Removing/Replacing the DT Disc & Cleaning the Dosing Station Removing the DP Disc and Cleaning the Dosing Station DP Discs Exchangeable Dosing ModulesDD Discs DT DiscsQTY Description Spare Parts DD Dosing UnitsQTY Description DT Dosing UnitsQTY Description DP Dosing UnitsAdditional Spare Parts DD/DT/DPRecipe Formulas Appendix a Basic Parameter SettingsDisc Appendix B Disc Sizing GuidesDisc Min/Max Single Station Digital Dosing Feeder Appendix C DrawingsDuo Digital Dosing Feeder Electrical Schematics of A250 Controller 882.01749.00 Appendix D Spare Parts List Replacement Motor Assembly Part NumbersDosing Disc/Shear Order Numbers Sterling, Inc Appendix E Technical Assistance882.01749.00