Sterling 882.01749.00 manual Removing the DP Disc and Cleaning the Dosing Station

Page 78

4-7 Removing the “DP” Disc and Cleaning the Dosing Station

1.Turn the control unit “Off”.

2.Disconnect the power supply.

3.Open the toggle latches.

4.Remove the dosing hopper (D).

5.Empty the dosing station.

6.Remove the profile clamp (C).

7.Remove the dosing hopper assembly (A and B).

8.Remove the wiper and traverse as described above.

9.Remove the four screws from the metering disc and lift the disc from the dosing unit housing.

10.Clean the components with a cotton cloth.

11.Clean the dosing hopper (A and B) in soapy water.

12.Dry all parts thoroughly.

13.Install the dosing hopper on the dosing module (locating the guide pin).

14.Install the profile clamp and tighten the screw.

15.Mount the dosing housing onto the dosing motor.

16.Close the toggle latches, securing the dosing module to the motor assembly.

882.01749.00

78 of 93

Image 78

Contents Digital Dosing Disc Additive Feeders Write Down Your Serial Numbers Here For Future Reference Shipping Info Unpacking and InspectionTable of Contents Appendix a Basic Parameter Settings Safety How to Use This ManualGeneral Safety Regulations ResponsibilityOperate this equipment within design specifications Functional Description IntroductionA250 Controller Duo Dual Station Digital Dosing FeederQuick Start-Up Guide UnpackingFeeder Configuration Injection Molding Motor and alarm utilty selection Encoder PulsesPage Injection molding Additive %Shot Size Screw Recovery Time Calibration weightDD Pellet Discs Disc DT Pellet & Regrind DiscsDP Powder Discs Additive Sample weighingRPM Page Recipe Setup for Simple Extrusion Throughput Feeder Configuration Extrusion follower 8400 Bodine Motor and alarm utilty selection Recipe Setup for Simple Extrusion Throughput Speed Weight Calibration Disc Calibration Number ThicknessScreen Screen Screen Installation and Operation Installation882.01749.00 TB #51 TB #54 Initial Operation Recipes Recipe MenuEnter / Edit Recipes Screw Recovery Time Simple Extrusion Recipe Extrusion Follower Recipe Throughput Speed Calibration Screen Screen Status screens PrerequisitesCommon Elements Buttons Speed Status Indicator Disc Motor IndicatorPress Signal Indicator Totalizer Screen Throughput ScreenMotor Speed Screen Screw Recovery Times Screen Injection only Manual Run / Jog ScreenConfiguration Navigation System Setup MenuSystem Setup Navigation Buttons 882.01749.00 882.01749.00 Feeder Type Encoder Pulses Maximum Motor SpeedManufacturer Motor Color Black & silver Drive Tuning Speed AlarmDefault Additive Measure Default Shot Size / Throughput Measure Injection Press Additive / Virgin Material Sensor Press Signal Type. Extrusion Follower only Minimum Press Signal. Extrusion Follower onlyMaximum Press Signal. Extrusion Follower only Passwords Screen Digital I/O Monitor Optional Features Level switches probesAnalog / Encoder Monitor Level Sensor Adjustment Screw Communication Protocol Interfaces Optional Additive Hoppers882.01749.00 Virgin Material Supply Hoppers Maintenance Preventative Maintenance IntervalsDD Dosing Module Pellets Installing the shear Removing the Shear Plate DD dosing ModuleRemoving the shear Removing the DD Disc and Cleaning the Dosing Module Dismantling the Dosing ModuleInstalling the Dosing Module Installing Different Types of Dosing DiscsDT Dosing Module Pellets and Some Regrind Removing/Replacing the Wiper in the DT Dosing Station Removing the DT Disc and cleaning the dosing station DP Powder Dosing Module Removing/Replacing the DT Disc & Cleaning the Dosing Station Removing the DP Disc and Cleaning the Dosing Station DT Discs Exchangeable Dosing ModulesDD Discs DP DiscsSpare Parts DD Dosing Units QTY DescriptionDT Dosing Units QTY DescriptionDP Dosing Units QTY DescriptionDD/DT/DP Additional Spare PartsAppendix a Basic Parameter Settings Recipe FormulasAppendix B Disc Sizing Guides DiscDisc Min/Max Appendix C Drawings Single Station Digital Dosing FeederDuo Digital Dosing Feeder Electrical Schematics of A250 Controller 882.01749.00 Appendix D Spare Parts List Replacement Motor Assembly Part NumbersDosing Disc/Shear Order Numbers Appendix E Technical Assistance Sterling, Inc882.01749.00