Hobart Welding Products OM-945 manual Servicing Air Cleaner Kohler−Powered Units, Stop engine

Page 35

9-3. Servicing Air Cleaner (Kohler−Powered Units)

1

2

oil

Notes

YStop engine.

YDo not run engine without air cleaner or with dirty element.

1 Wrapper

Wash wrapper with soap and water solution. Allow wrapper to air dry completely.

Spread 1 tablespoon SAE 30 oil evenly into wrapper. Squeeze out excess oil.

2 Element

Replace element if damaged, dirty, or oily.

aircleaner3 11/04 − 802 772 / S-0759

Start Your Professional Welding Career Now!

400 Trade Square East, Troy, Ohio 45373

1-800-332-9448 www.welding.org

Over 80,000 trained

since 1930!

OM-945 Page 31

Page 34 Page 36
Image 35
Page 34 Page 36
Contents
Description ProcessesFrom Hobart to You Table of Contents Options and Accessories Warranty Arc Welding Hazards Symbol UsageEngine Hazards Compressed Air Hazards Radiation can cause interference Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationLES Fumées ET LES GAZ peuvent être dangereux Signification des symboles− Consignes DE Sécurité − Lire Avant Utilisation UN Choc Électrique peut tuerLE Bruit peut affecter l’ouïe LE Soudage peut provoquer un in- cendie ou une explosionDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Étincelles Volantes risquent de provoquer des blessures ’AIR Comprimé peut provoquer des blessures’EMPLOI Excessif peut LE Surchauffement peut endom- mager le moteur électriqueEn ce qui concerne les stimulateurs cardiaques LE Soudage À L’ARC risque de provoquer des interférencesPour les moteurs à essence Pour les moteurs diesel− Definitions − SpecificationsSymbol Definitions Weld, Power, and Engine SpecificationsGenerator Power Curve Dimensions, Weights, and Operating AnglesDuty Cycle Fuel Consumption All ModelsVolt-Ampere Curves Material Thickness Reference ChartMounting − InstallationInstalling Welding Generator Vehicle frame. Always connect a ground wireOil Engine Prestart Checks Robin-Powered UnitsEngine Prestart Checks Kohler-Powered Units FuelConnect negative − Activating The Dry Charge Battery If ApplicableConnecting the Battery Do not overfill battery cellsWeld Output Terminals Installing Exhaust PipeSelecting Weld Cable Sizes Connecting To Weld Output TerminalsFront Panel Controls − Operating the Welding GeneratorLoaded Cold Weather Engine OperationAmperage Selection Table For Stick Smaw Electrodes InfrequentlyStandard Receptacles − Operating Auxiliary EquipmentGfci Receptacle Option Optional Generator Power ReceptaclesReceptacle Current Available in Amperes 240Routine Maintenance Robin-Powered Units − Maintenance ROBIN-POWERED UnitsMaintenance Label Robin-Powered Units Servicing Air Cleaner Robin−Powered Units Stop engine and let cool Overload Protection Robin-Powered UnitsServicing Optional Spark Arrestor Robin-Powered Units Stop engine. Disconnect nega- tive − battery cable Full Tools Needed Weld/Power Speed Adjustment Adjusting Engine Speed Robin-Powered UnitsIdle Speed Adjustment Routine Maintenance Kohler-Powered Units − Maintenance − KOHLER-POWERED UnitsMaintenance Label Kohler-Powered Units Servicing Air Cleaner Kohler−Powered Units Servicing Optional Spark Arrestor Kohler-Powered Units Overload Protection Kohler-Powered Units802 339-G / S-0842 Stop engine. Reinstall wrapper Adjusting Engine Speed Kohler-Powered UnitsWelding − TroubleshootingTroubleshooting Generator PowerEngine Work like a Pro − Electrical Diagram Grounding Generator To Truck Or Trailer Frame − Generator Power GuidelinesSelecting Equipment Amperes x Volts = Watts Grounding When Supplying Building SystemsHow Much Power Does Equipment Require? Earth ground if supplyingFarm/Home Equipment Rating Starting Watts Running Watts Approximate Power Requirements For Industrial MotorsApproximate Power Requirements For Farm/Home Equipment Industrial Motors Rating Starting Watts Running WattsContractor Rating Starting Watts Running Watts Approximate Power Requirements For Contractor EquipmentKVA/HP x HP x 1000 = Starting Amperage Power Required To Start MotorHow Much Power Can Generator Supply? Single-Phase Induction Motor Starting RequirementsTypical Connections To Supply Standby Power Current Load Watts Amperes Selecting Extension Cord Use Shortest Cord Possible− Stick Welding Smaw Guidelines Stick Welding ProcedureWeld current starts when electrode touches work- piece Striking an Arc − Tapping Technique Electrode and Amperage Selection ChartStriking an Arc − Scratch Start Technique Positioning Electrode Holder Poor Weld Bead CharacteristicsGood Weld Bead Characteristics Electrode Movement During Welding Conditions That Affect Weld Bead ShapeTee Joint Butt JointsLap Joint Possible Causes Corrective Actions Troubleshooting − PorosityTroubleshooting − Excessive Spatter Weld TestTroubleshooting − Excessive Penetration Troubleshooting − Incomplete FusionTroubleshooting − Lack Of Penetration Troubleshooting − Distortion Troubleshooting − Burn-ThroughTroubleshooting − Waviness Of Bead Main Assembly Robin Engine Shown − Parts ListMain Assembly Panel, Front w/Components Panel, Front w/Components -1Item Generator -1Item Assistance ServiceSupport Hobart Welding Products Contact your Distributor for
Related manuals
Manual 68 pages 57.29 Kb
Top Page Image Contents