Hobart Welding Products OM-474 manual Parts List, 101 102 105 104 103

Page 52

SECTION 11 – PARTS LIST

.Hardware is common and not available unless listed.

	3	4
		5
		6
2		14	15
1		7

19	26	27
20

121

120

119

118

117

1013

115

	68	25
	68	76
		76
	21	24
	21	77
	22	77
	22
	23

116114

113

112

111

110

109

108

106 107

Fig 11-4

100	98
	97
	96	94	93
	95	94	93
	101
	102		92
	102

105	104	103
		103

8382

91 90

Figure 11-1. Main Assembly

OM-474 Page 48

Image 52

Contents OM-474 ProcessesDescription JulyFrom Hobart to You Table of Contents Page Symbol Usage Arc Welding HazardsElectric Shock can kill ARC Rays can burn eyes and skinEngine Hazards Battery Explosion can Blind Moving Parts can cause injuryEngine Exhaust Gases can kill Engine Heat can cause firePrincipal Safety Standards EMF InformationRadiation can cause interference ARC Welding can cause interferenceSignification des symboles Consignes DE Sécurité Lire Avant UtilisationUN Choc Électrique peut tuer LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in- cendie ou une explosion DES Particules Volantes peuvent blesser les yeuxDES Pièces Chaudes peuvent provoquer des brûlures graves LE Bruit peut affecter l’ouïeDES Organes Mobiles peuvent provoquer des blessures ’EXPLOSION DE LA Batterie peutLA Chaleur DU Moteur peut pro- voquer un incendie LA Chute DE L’APPAREIL peut blesserPrincipales normes de sécurité Information sur les champs électromagnétiquesLE Soudage À L’ARC risque de provoquer des interférences Consignes relatives aux stimulateurs cardiaquesSpecifications Symbols And DefinitionsWeld, Power, And Engine Specifications DefinitionsDimensions, Weights, And Operating Angles DimensionsWeight Fuel ConsumptionAC Auxiliary Power Duty Cycle And Overheating60% Duty Cycle At 350 Amperes Minutes Welding5 KVA/KW Single-Phase Auxiliary Power Plant No Weld Load Optional AC Power Plant Curves12.5 KVA/KW Three-Phase Auxiliary Power Plant No Weld Load Volt-Ampere Curves DC Volts CC/DC StandardAC Amperes CV/DC Models with Optional CV-3 Module 100 Ranges 190-Max 110-270Installing Welding Generator InstallationConnecting The Battery Installing Muffler Temperatures below 0 F -18C 13 mm Full Diesel Valve OpenEngine Prestart Checks Do not use gasoline. Gasoline will damage engineConnecting To Weld Output Terminals Selecting Weld Cable Sizes100 ft 30 m Or Less 10 100% Duty CycleRemote 14 Receptacle RC3 Information Optional, See Section Terminal Strip 3T Connections OptionalSocket Information Stop engineOperating Welding Generator Front Panel Controls See SectionAmpere Range Switch Do not switch under loadDescription Of Front Panel Controls See Section Stop engine and fix trouble if either warning light goes onRemote Control Optional Example Combination remote amperage controlOperating Auxiliary Equipment Volt Duplex And Optional Gfci ReceptaclesVolt Duplex Receptacle Optional Open ContactSet Engine Control switch to Run when using auxiliary power Connecting Optional Auxiliary Power PlantFront Maintenance and Troubleshooting Maintenance Label To Clean air filter Servicing Air CleanerDo not clean housing with air hose Servicing Fuel System Stop engine and let coolTo drain water from fuel system To replace fuel filterIdle Speed Adjustment Adjusting Engine SpeedEngine Speed No Load Changing Engine Oil And Filter Overload Protection If any fuse or circuit breakerInspecting And Cleaning Optional Spark Arrestor Muffler TroubleshootingWelding Trouble RemedyAuxiliary Power Coolant temperature gets too high see Section Check engine control switch, and replace if necessaryEngine See engine manualOM-474 Electrical Diagrams Circuit Diagram For Welding Generator For Standard ModelsOM-474 193 989-B RUN-IN Procedure WetstackingRun-In Procedure Using Load Bank Load BankRun-In Procedure Using Resistance Grid Do not touch hot exhaustBank/grid From flammablesSelecting Equipment Auxiliary Power GuidelinesGrounding Generator To Truck Or Trailer Frame Grounding When Supplying Building Systems How Much Power Does Equipment Require?Earth ground if supplying Use ground device as stated in electrical codesApproximate Power Requirements For Industrial Motors Approximate Power Requirements For Farm/Home EquipmentIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running WattsApproximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running WattsPower Required To Start Motor How Much Power Can Generator Supply?Single-Phase Induction Motor Starting Requirements KVA/HP x HP xTypical Connections To Supply Standby Power Welding Generator Auxiliary Power output circuitItem 4 is not necessary if circuit Protection is already presentSelecting Extension Cord Use Shortest Cord Possible Current Load Watts AmperesParts List 101 102 105 104 10365 66 Includes Items Dia Part Description Mkgs Quantity PLG9,RC9 PC4 Control Box w/Components -4 Item Control Box w/ComponentsGenerator Generator -1 Item Panel, Front w/Components Panel, Front w/Components -1 Item Page Service SupportHobart Welding Products Contact your Distributor forCall