Bosch Appliances 4100-09, 4100DG manual Adjustments, Adjusting 0 Degree Positive Stops

Page 34

Adjustments

Adjusting 0 and 45

Degree Positive Stops

Your saw is equipped with positive stops for fast and accurate positioning of the saw blade at 90 and 45 degrees to the table.

!

WARNING

To prevent personal injury, always disconnect

plug from power source when making

 

 

adjustments.

1.Turn elevation wheel 2 clockwise and raise blade to maximum height (Fig. 16).

Adjusting 0 Degree Positive Stop:

2.Loosen the blade tilt lock handle 1 and push the elevation wheel 2 to the left as far as possible and tighten the blade tilt lock handle 1 (Fig. 16).

3.Place a combination square on the table with one end of square against the blade as shown (Fig. 17), and check to see if the blade is 90 degrees to the table. If the blade is not 90 degrees to the table, loosen the blade tilt lock handle 1, loosen 90 degree adjustment screw 4, loosen 90 degree bevel stop cam 5 and push the elevation wheel until the blade is 90 degrees to the table.

4.Tighten blade tilt lock handle 1, rotate the bevel stop cam 5 until it touches the bevel stop housing 7, then tighten 90 degree adjustment screw 3 .

5.Loosen adjustment screw 6 and adjust pointer 3 to indicate 0 degrees on the bevel scale.

Adjusting 45 Degree Positive Stop:

6.Loosen the blade tilt lock handle 1 and push the elevation wheel 2 to the right as far as possible and tighten the blade tilt lock handle 1.

7.Place a combination square on the table with one end of square against the blade as shown (Fig. 18), and check to see if the blade is 45 degrees to the table. If the blade is not 45 degrees to the table, loosen the blade tilt lock handle 1, loosen 45 degree adjustment screw 8, loosen 45 degree bevel stop cam 9 and push the elevation wheel until the blade is 45 degrees to the table.

8.Tighten blade tilt lock handle 1, rotate the 45 degree bevel stop cam 9 until it touches the bevel stop housing 7, then tighten 45 degree adjustment screw 8.

FIG. 16

 

 

 

9

8

5

4

3

1

 

 

 

 

 

 

 

 

 

 

 

 

 

2

6 7

FIG. 17

FIG. 18

34.

Image 34
Contents 4100 4100DG Work Area General Safety RulesPersonal Safety Tool UseAdditional Safety Rules Tool CareKnow Your Cutting Tools Double Insulated Tools Think SafetyWhen SERVICING, USE only Identical Replace Extension CordsTable of Contents Tools Needed For Assembly Glossary of TermsSécurité de l’utilisateur Consignes générales de sécuritéZone de travail Utilisation de l’outilConsignes de sécurité supplémentaires Entretien de l’outilFigurant À L’AVANT DE Votre Scie DE Table FAMILIARISEZ-VOUS Avec VOS Outils DE CoupeLA Sécurité Avant Tout Double isolationRallonges IdentiquesTable des matières Lexique Outils nécessaires à l’assemblageSeguridad personal Normas generales de seguridadArea de trabajo Utilización de la herramientaNormas de seguridad adicionales Cuidado de la herramientaConozca SUS Herramientas DE Corte Piense EN LA Seguridad Herramientas con aislamiento dobleCordones de extensión Unicamente Piezas DE Repuesto IdenticasIndice Ajuste de los topes positivos de 90 y 45 grados 34-35Glosario de términos Herramientas necesarias para el ensamblajeGetting To Know Your Table Saw 13 1 4Familiarisez-vous avec Votre scie de table Familiarización con la Sierra de mesaTable Insert Smart Guard SystemSmart Guard System Storage Digital Carriage Model 4100DG-09 only21. Élément Amovible DE LA Table DE Coupe Système Smart GuardRangement DU Système Smart Guard Chariot Numérique Modèle 4100DG-09 SeulementUnpacking and Checking Contents Liste des pièces fournies Ouverture de l’emballage et Vérification du contenuDesempaquetado y Tabla de piezas sueltasAttaching the Smart Guard System Positioning the Riving KnifePositionnement DU Couteau Diviseur AssemblageEnsamblajeMontage du système Smart Guard Posicionamiento DE LA Cuchilla SeparadoraAttaching the Guard Assembly Attaching the ANTI-KICKBACK DeviceInstalación DEL Ensamblaje DEL Protector Montage DE Lensemble DE Barrière DE SecuriteInstalación DEL Dispositivo Antirretroceso Changing The Blade Changement de la lame Cambio de la hojaAttaching Rip Fence AssemblyMounting Table Saw 16 hex nutsMontage du guide de refente Installation de la scie De tableMontaje de la sierra de Mesa Colocación del tope-guía Para cortar al hiloAdjusting 0 Degree Positive Stop AdjustmentsAdjusting 0 Degree Positive Stops Adjusting 45 Degree Positive StopRéglage des butées fixes 90 et RéglagesAjustesAjuste de los topes positivos De 90 y 45 grados Miter Gauge Adjustment Adjusting Blade Parallel To Miter Gauge SlotsUnder Front 2TABLE Under Rear of Table Ajuste del calibre de ingletes Realizar cualquier ajusteAligning Rip Fence Rip Fence Pointer AdjustmentTo set the rip fence pointer Alineación del tope-guía para Cortar al hilo Alignement du guide de refenteRéglage de l’indicateur du guide De refente Ajuste del indicador del tope-guía Para cortar al hiloTable Pointer Adjustment Adjusting The Table InsertRéglage de lélément rapporté De la table Réglage de l’indicateur de la tableAjuste del indicador de la mesa Ajuste del accesorio de inserción De la mesaChecking Riving Knife Alignment Adjusting Riving KnifeRiving Knife Alignment Work Bois MaderaRéglage du couteau diviseur Alignement du Couteau DiviseurAlineación de la Cuchilla Separadora Comprobación de la alineación de la cuchilla SeparadoraSmart Guard System Safety Power SwitchBasic Table Saw Operation ❶Component Parts figureSystème Smart Guard Funcionamiento básico de La sierra de mesaInterrupteur de sûreté Interruptor de encendido De seguridadExtending Table Extension Blade Bevel ControlSystem Storage Control de inclinación de la hoja Réglage de l’inclinaison de la lameRéglage de la rallonge de table Ajuste de la extensión de la mesaBosch Digital Carriage Installing 9 Volt BatteryFeatures see figures 37 Model DC010Chariot numérique Bosch Carro digital BoschON/OFF Button and Memory see figure Reset button see figures 39Control Buttons and Display Automatic Shut OffBotones de control y pantalla Display Changes Left Zero Out the Display see figures 40Display Changes Right To Zero OutRemise à zéro de lécran daffichage Voir Figures 40 Cambios en la pantalla, a la derecha delCambios en la pantalla, a la izquierda del Changements de laffichage Droite de « 0 »Connecting Digital Carriage To Rip Fence Connexion du chariot numérique Au guide de refente Conexión del carro digital al tope-guía Para cortar al hiloExtended Right Side Rip Cuts 13-1/2 to 25 fig Setting Fence with Digital CarriageRight Side Rip Cuts 0 to 13-1/2 fig Left Side Rip Cuts figCoupes longitudinales du côté gauche Fig Ajuste del tope-guía con el carro digitalCoupes longitudinales du côté droit de 0 po à 13 1/2 po Fig Cortes al hilo en el lado derecho de 0 a 13-1/2 figBevel Rip Cuts Right side only CleaningMaintaining the Digital Carriage Parking Position see figureEntretien du chariot numérique Mantenimiento del carro digitalPre-Cut Locator Using The Rip Fence Pointer When Table Is Not ExtendedUsing The Table Pointer When Table Is Extended Making Rip Cuts Beyond Inches Without The Use Of ScaleUbicador de precorte Repère de sciageSans utiliser d’échelle graduée Push Stick and Push Block Make the Push Stick 1 using a piece of 1 x 2 as shown FigWork Helpers Auxiliary FenceAyudantes de trabajo Accessoires de sciageGuide de coupe auxiliaire Palo de empujar y bloque de empujarSafety precautions in addition to the safety Using The Miter GaugeTo adjust the miter angle Miter Gauge Auxiliary FacingCalibre de ingletes Utilización del calibre de ingletesGuide de coupe angulaire Réglage du guide de coupe angulaireCrosscutting Corte transversal Coupe transversaleOtra Razon Making the Facing Block AssemblyRepetitive Crosscutting Parts RequiredCoupe transversale répétitive Realización DEL Corte Transversal RepetitivoBevel Crosscutting Using the Rip FenceMiter Cutting Compound Miter CuttingCoupe angulaire biseautée Coupe angulaireCoupe transversale biseautée Utilisation du guide de refenteDIA Hole RIP Fence Auxiliary FacingPièce Dappoint Auxiliaire Pour LE Guide DE Refente Refrentado Auxiliar Para EL TOPE-GUÍA Para Cortar AL HiloRipping Bevel RippingCoupe EN Long Biseautée Coupe en longCorte AL Hilo EN Bisel Rabbeting Non Thru-SawingBe Positive They are Securely Attached Réalisation de feuillures Coupe partielleAserrado no pasante Corte de rebajosDado and Molding Cutting Installing a Dado SETUsing Stacked Dado Sets To reduce the risk of injury, do not use dadoUtilisation Densembles DE Lames a Rainurer Empilees Installation DUN Ensemble DE Lames a RainurerCorte de mortajas y molduras Instalacion DE UN Juego DE MortajarAdjustable or Wobble Dado Sets Returning SAW to Normal THRU-CUTTINGJuegos DE Mortajar Ajustables U Oscilantes Regreso DE LA Sierra a Corte Pasante NormalEnsembles DE Lames a Rainurer Reglables OU Oscillantes Plug from power source before changing Installing a Molding Head SETHands over the cutting molding head cutters Instalacion DE UN Juego DE Fresas DE Moldurar Installation DUN Ensemble DE Lames a MoulurerRegreso DE LA Sierra a Corte Pasante Normal Special Cutting Techniques MaintenanceMaintaining Your Table Saw Cutting Metals and MasonryEntretien de la scie de table Mantenimiento de la sierra De mesaImproper accessories may cause hazards Recommended AccessoriesUse only recommended accessories. Follow LubricationLubricación Accessoires recommandés Accesorios recomendadosLubrification ArticleTrouble Shooting Guide de diagnosticAveria Vibracion Excesiva Localización y reparación De averíasAveria LA Sierra no Arranca Averia no SE Puede Hacer UN Corte EN Angulo RectoFollow Steps Suivez LES Étapes Siga LOS Pasos Comme indiqué ci-dessus, et fixez-le avec du ruban adhésifPage Limited Warranty of Bosch Portable and Benchtop Power Tools

4100DG, 4100-09, 4100 specifications

Bosch Appliances 4100, 4100-09, and 4100DG are a series of highly regarded kitchen appliances designed to enhance efficiency and performance in home cooking. Bosch has a long-standing reputation for crafting high-quality products, and this series is no exception. Each model combines cutting-edge technology with sleek design to meet the needs of modern households.

A standout feature of the Bosch 4100 series is its powerful performance. These appliances come equipped with high-performance motors and advanced cooking capabilities that ensure consistent results. Whether baking, broiling, or roasting, users can expect even heat distribution and precise temperature control, which are critical for achieving culinary perfection.

The 4100 appliances also emphasize intuitive usability, featuring easy-to-navigate controls and thoughtful design. The models include user-friendly digital displays and simple button interfaces, making it easy for anyone, regardless of cooking experience, to operate them seamlessly. Additionally, the Bosch 4100 series is designed with a focus on safety, incorporating advanced systems that prevent overheating and ensure secure operation.

In terms of design, the Bosch 4100 models boast a streamlined aesthetic that blends well with any kitchen décor. Constructed from high-quality materials, they offer durability while exuding a modern, sophisticated look. The stainless-steel finishes not only add elegance but are also easy to clean and maintain, making them practical for everyday use.

Another noteworthy characteristic of the Bosch 4100 series is the energy efficiency standards they meet. These appliances are designed to utilize less energy without compromising performance, helping homeowners save on utility bills while minimizing their environmental footprint.

The 4100DG model specifically stands out for its dual-fuel capabilities, allowing users to harness the benefits of both gas and electric cooking methods. This versatility provides chefs with greater flexibility and precision, accommodating a variety of cooking styles and preferences.

Overall, Bosch Appliances 4100, 4100-09, and 4100DG exemplify craftsmanship and innovation in the kitchen appliance sector. Their combination of advanced technology, user-friendly features, and stylish designs make them an excellent choice for anyone looking to elevate their cooking experience and enhance their kitchen functionality.