Miter Gauge Adjustment

Adjusting Blade Parallel To

The Miter Gauge Slots

The blade was adjusted parallel to the miter gauge slots at the factory. In order to insure accurate cuts and help prevent kickback, this adjustment should be rechecked. If adjustment is necessary, follow the steps below.

To prevent personal injury, always discon- ! WARNING nect the plug from power source before mak-

ing any adjustments.

1.Turn elevation wheel and raise blade as high as it will go.

2.Select a point on the body of the saw blade that is set to the left when viewing blade from the front of saw, and mark 1 with a pencil (Fig. 19).

3.Place the base of a combination square against the edge of the miter gauge slot, and extend the sliding rule of square so it just touches the marked point 1 on the body of the saw blade at the rear of the table.

4.Rotate blade and check the same marked point 1 of the saw blade at the front of the table (Fig. 19).

5.If the front and back measurements, shown in Figure 19, are not identical, loosen the four alignment bolts 2, located on the underside of the table at the front and rear of the saw with hex wrench supplied with your saw (Fig. 20 & 21). Carefully move the saw blade until the blade is parallel to the miter gauge slot, and securely tighten all four bolts.

To check your miter gauge accuracy, move the miter gauge in line with blade and use a combination square to make sure the miter gauge body is 90 degress to the blade (Fig. 22).

To adjust the miter gauge for 90 degrees:

1.Loosen lock nut 3, adjustment screw 4, and lock knob 5.

2.Flip stop plate 6 down.

3.Rotate miter gauge body until it is 90 degrees to the blade.

4.Tighten lock knob 5.

5.Flip stop plate 6 up and tighten adjustment screw 4 until it contacts stop plate 6.

6.Tighten lock nut 8.

7.If pointer 7 is not pointing to 90 degrees, loosen set screw 8 on side of miter gauge bar and rotate pointer 7 to 90 degrees mark. Tighten set screw 8.

8.To adjust the miter gauge for 45 degress left and right, repeat steps 1-6, but use 45 degree stops.

FIG. 19

FIG. 20

UNDER FRONT OF

2TABLE

UNDER REAR OF TABLE

FIG. 21

FIG. 22

3	30
0

		45		5
		60		4
		60		6
		75		0
		75	90	75
6	3	4
	8

36.

4100DG, 4100-09, 4100 specifications

Bosch Appliances 4100, 4100-09, and 4100DG are a series of highly regarded kitchen appliances designed to enhance efficiency and performance in home cooking. Bosch has a long-standing reputation for crafting high-quality products, and this series is no exception. Each model combines cutting-edge technology with sleek design to meet the needs of modern households.

A standout feature of the Bosch 4100 series is its powerful performance. These appliances come equipped with high-performance motors and advanced cooking capabilities that ensure consistent results. Whether baking, broiling, or roasting, users can expect even heat distribution and precise temperature control, which are critical for achieving culinary perfection.

The 4100 appliances also emphasize intuitive usability, featuring easy-to-navigate controls and thoughtful design. The models include user-friendly digital displays and simple button interfaces, making it easy for anyone, regardless of cooking experience, to operate them seamlessly. Additionally, the Bosch 4100 series is designed with a focus on safety, incorporating advanced systems that prevent overheating and ensure secure operation.

In terms of design, the Bosch 4100 models boast a streamlined aesthetic that blends well with any kitchen décor. Constructed from high-quality materials, they offer durability while exuding a modern, sophisticated look. The stainless-steel finishes not only add elegance but are also easy to clean and maintain, making them practical for everyday use.

Another noteworthy characteristic of the Bosch 4100 series is the energy efficiency standards they meet. These appliances are designed to utilize less energy without compromising performance, helping homeowners save on utility bills while minimizing their environmental footprint.

The 4100DG model specifically stands out for its dual-fuel capabilities, allowing users to harness the benefits of both gas and electric cooking methods. This versatility provides chefs with greater flexibility and precision, accommodating a variety of cooking styles and preferences.

Overall, Bosch Appliances 4100, 4100-09, and 4100DG exemplify craftsmanship and innovation in the kitchen appliance sector. Their combination of advanced technology, user-friendly features, and stylish designs make them an excellent choice for anyone looking to elevate their cooking experience and enhance their kitchen functionality.