Bosch Appliances 4100-09 Installing a Molding Head SET, Plug from power source before changing

Page 82

INSTALLING A MOLDING HEAD SET

A Molding Head Set may be used to add a variety of decorative edges to a wood work piece. These edges are commonly seen on trim moldings and furniture.

!

WARNING

To reduce the risk of injury, always disconnect

plug from power source before changing

blades.

 

 

 

To reduce the risk of injury, always use the

!

WARNING

Bosch Molding Table Insert No.TS1009. Never

 

 

make molding head cuts without this insert. Do not use molding head sets larger than 7” diameter and with cutters wider than 1”. Never set molding cutters to any bevel angle other than the vertical 0° angle. Follow all warnings and instructions shown here and those that accompany your molding head set. Failure to comply with these warnings may result in serious bodily injuries.

NOTE: Leave the inner washer in its original sawing position. Install molding head, then outer washer, and then arbor nut. Check that all cutters and the arbor nut are securely tightened. Some molding head sets come with an additional thick washer/spacer; this part is not used on the 4100 table saw.

1.Disconnect plug from power source. Raise saw blade to maximum height.

2.Remove the Barrier Guard Assembly and Anti-Kickback Device (see page 26). Lower and lock the Riving Knife in its lowest position.

3.Remove standard table insert plate.

4.Remove the arbor nut and only the outer blade washer and saw blade (see page 30). NOTE: Leave inner blade washer on arbor shaft.

5.Place molding head against inner washer (with cutters facing to front of saw). Then place on the outer washer and tighten arbor nut on arbor shaft.

6.Lower the cutters below the table top and insert the Bosch Molding Table Insert (TS1009) (Fig. 72). Raise the cutters to the desired depth of cut (above the insert). Check that the tool is not plugged into a power source; then carefully rotate the cutters by hand to make sure all components are tightly held and no interferences exist.

7.Plug saw into power source. Using scrap wood, make practice molding cuts and adjust height accordingly.

!

WARNING

To reduce the risk of injury, never pass your

hands over the cutting molding head cutters.

 

 

Molding cuts are non-thru (blind) cuts. Many times the cutters can not be seen during cutting. See page 76 for instructions on non- thru sawing. The work piece must be held against the saw's fence as it is being fed. An auxiliary fence should be attached to the saw's fence (see page 72). Never make freehand cuts. Whenever possible, use push sticks and push blocks for molding cutting (see page 74). Use feather boards and hold-downs, attached to the table or fence (See page 76). IMPORTANT: Follow all instructions and warnings that come with your molding head set.

RETURNING SAW TO NORMAL THRU-CUTTING

After completing your Molding cutting, be sure to return the inner and outer washers to the original positions (see page 30 for details). It is important that the original equipment washers are in the proper positions so that the saw blade always aligns with the permanently installed riving knife.

FIG. 71

INNER BLADE WASHER

RONDELLE DE LAME

INTERIEURE

ARANDELA INTERIOR

DE LA HOJA

FIG. 72

ARBOR NUT

ECROU DE FIXATION DE

L'ARBRE

TUERCA DEL EJE

PORTAHERRAMIENTA

OUTER WASHER

RONDELLE EXTERIEURE

ARANDELA EXTERIOR

MOLDING HEAD

ENSEMBLE DE LAMES A

MOULURER

FRESA DE MOLDURAR

MOLDING TABLE INSERT

PLAQUE AMOVIBLE DE

TABLE POUR MOULURAGE

ACCESORIO DE INSERCIÓN

DE LA MESA DE MOLDURAR

82.

Page 81 Page 83
Image 82
Page 81 Page 83
Contents 4100 4100DG Work Area General Safety RulesPersonal Safety Tool UseAdditional Safety Rules Tool CareKnow Your Cutting Tools Double Insulated Tools Think SafetyWhen SERVICING, USE only Identical Replace Extension CordsTable of Contents Tools Needed For Assembly Glossary of TermsSécurité de l’utilisateur Consignes générales de sécuritéZone de travail Utilisation de l’outilConsignes de sécurité supplémentaires Entretien de l’outilFigurant À L’AVANT DE Votre Scie DE Table FAMILIARISEZ-VOUS Avec VOS Outils DE CoupeLA Sécurité Avant Tout Double isolationRallonges IdentiquesTable des matières Lexique Outils nécessaires à l’assemblageSeguridad personal Normas generales de seguridadArea de trabajo Utilización de la herramientaNormas de seguridad adicionales Cuidado de la herramientaConozca SUS Herramientas DE Corte Piense EN LA Seguridad Herramientas con aislamiento dobleCordones de extensión Unicamente Piezas DE Repuesto IdenticasIndice Ajuste de los topes positivos de 90 y 45 grados 34-35Glosario de términos Herramientas necesarias para el ensamblajeGetting To Know Your Table Saw 13 1 4Familiarisez-vous avec Votre scie de table Familiarización con la Sierra de mesaTable Insert Smart Guard SystemSmart Guard System Storage Digital Carriage Model 4100DG-09 only21. Élément Amovible DE LA Table DE Coupe Système Smart GuardRangement DU Système Smart Guard Chariot Numérique Modèle 4100DG-09 SeulementUnpacking and Checking Contents Liste des pièces fournies Ouverture de l’emballage et Vérification du contenuDesempaquetado y Tabla de piezas sueltasAttaching the Smart Guard System Positioning the Riving KnifePositionnement DU Couteau Diviseur AssemblageEnsamblajeMontage du système Smart Guard Posicionamiento DE LA Cuchilla SeparadoraAttaching the Guard Assembly Attaching the ANTI-KICKBACK DeviceInstalación DEL Ensamblaje DEL Protector Montage DE Lensemble DE Barrière DE SecuriteInstalación DEL Dispositivo Antirretroceso Changing The Blade Changement de la lame Cambio de la hojaAttaching Rip Fence AssemblyMounting Table Saw 16 hex nutsMontage du guide de refente Installation de la scie De tableMontaje de la sierra de Mesa Colocación del tope-guía Para cortar al hiloAdjusting 0 Degree Positive Stop AdjustmentsAdjusting 0 Degree Positive Stops Adjusting 45 Degree Positive StopRéglage des butées fixes 90 et RéglagesAjustesAjuste de los topes positivos De 90 y 45 grados Miter Gauge Adjustment Adjusting Blade Parallel To Miter Gauge SlotsUnder Front 2TABLE Under Rear of Table Ajuste del calibre de ingletes Realizar cualquier ajusteAligning Rip Fence Rip Fence Pointer AdjustmentTo set the rip fence pointer Alineación del tope-guía para Cortar al hilo Alignement du guide de refenteRéglage de l’indicateur du guide De refente Ajuste del indicador del tope-guía Para cortar al hiloTable Pointer Adjustment Adjusting The Table InsertRéglage de lélément rapporté De la table Réglage de l’indicateur de la tableAjuste del indicador de la mesa Ajuste del accesorio de inserción De la mesaChecking Riving Knife Alignment Adjusting Riving KnifeRiving Knife Alignment Work Bois MaderaRéglage du couteau diviseur Alignement du Couteau DiviseurAlineación de la Cuchilla Separadora Comprobación de la alineación de la cuchilla SeparadoraSmart Guard System Safety Power SwitchBasic Table Saw Operation ❶Component Parts figureSystème Smart Guard Funcionamiento básico de La sierra de mesaInterrupteur de sûreté Interruptor de encendido De seguridadExtending Table Extension Blade Bevel ControlSystem Storage Control de inclinación de la hoja Réglage de l’inclinaison de la lameRéglage de la rallonge de table Ajuste de la extensión de la mesaBosch Digital Carriage Installing 9 Volt BatteryFeatures see figures 37 Model DC010Chariot numérique Bosch Carro digital BoschON/OFF Button and Memory see figure Reset button see figures 39Control Buttons and Display Automatic Shut OffBotones de control y pantalla Display Changes Left Zero Out the Display see figures 40Display Changes Right To Zero OutRemise à zéro de lécran daffichage Voir Figures 40 Cambios en la pantalla, a la derecha delCambios en la pantalla, a la izquierda del Changements de laffichage Droite de « 0 »Connecting Digital Carriage To Rip Fence Connexion du chariot numérique Au guide de refente Conexión del carro digital al tope-guía Para cortar al hiloExtended Right Side Rip Cuts 13-1/2 to 25 fig Setting Fence with Digital CarriageRight Side Rip Cuts 0 to 13-1/2 fig Left Side Rip Cuts figCoupes longitudinales du côté gauche Fig Ajuste del tope-guía con el carro digitalCoupes longitudinales du côté droit de 0 po à 13 1/2 po Fig Cortes al hilo en el lado derecho de 0 a 13-1/2 figBevel Rip Cuts Right side only CleaningMaintaining the Digital Carriage Parking Position see figureEntretien du chariot numérique Mantenimiento del carro digitalPre-Cut Locator Using The Rip Fence Pointer When Table Is Not ExtendedUsing The Table Pointer When Table Is Extended Making Rip Cuts Beyond Inches Without The Use Of ScaleUbicador de precorte Repère de sciageSans utiliser d’échelle graduée Push Stick and Push Block Make the Push Stick 1 using a piece of 1 x 2 as shown FigWork Helpers Auxiliary FenceAyudantes de trabajo Accessoires de sciageGuide de coupe auxiliaire Palo de empujar y bloque de empujarSafety precautions in addition to the safety Using The Miter GaugeTo adjust the miter angle Miter Gauge Auxiliary FacingCalibre de ingletes Utilización del calibre de ingletesGuide de coupe angulaire Réglage du guide de coupe angulaireCrosscutting Corte transversal Coupe transversaleOtra Razon Making the Facing Block AssemblyRepetitive Crosscutting Parts RequiredCoupe transversale répétitive Realización DEL Corte Transversal RepetitivoBevel Crosscutting Using the Rip FenceMiter Cutting Compound Miter CuttingCoupe angulaire biseautée Coupe angulaireCoupe transversale biseautée Utilisation du guide de refenteDIA Hole RIP Fence Auxiliary FacingPièce Dappoint Auxiliaire Pour LE Guide DE Refente Refrentado Auxiliar Para EL TOPE-GUÍA Para Cortar AL HiloRipping Bevel RippingCoupe EN Long Biseautée Coupe en longCorte AL Hilo EN Bisel Rabbeting Non Thru-SawingBe Positive They are Securely Attached Réalisation de feuillures Coupe partielleAserrado no pasante Corte de rebajosDado and Molding Cutting Installing a Dado SETUsing Stacked Dado Sets To reduce the risk of injury, do not use dadoUtilisation Densembles DE Lames a Rainurer Empilees Installation DUN Ensemble DE Lames a RainurerCorte de mortajas y molduras Instalacion DE UN Juego DE MortajarAdjustable or Wobble Dado Sets Returning SAW to Normal THRU-CUTTINGJuegos DE Mortajar Ajustables U Oscilantes Regreso DE LA Sierra a Corte Pasante NormalEnsembles DE Lames a Rainurer Reglables OU Oscillantes Plug from power source before changing Installing a Molding Head SETHands over the cutting molding head cutters Instalacion DE UN Juego DE Fresas DE Moldurar Installation DUN Ensemble DE Lames a MoulurerRegreso DE LA Sierra a Corte Pasante Normal Special Cutting Techniques MaintenanceMaintaining Your Table Saw Cutting Metals and MasonryEntretien de la scie de table Mantenimiento de la sierra De mesaImproper accessories may cause hazards Recommended AccessoriesUse only recommended accessories. Follow LubricationLubricación Accessoires recommandés Accesorios recomendadosLubrification ArticleTrouble Shooting Guide de diagnosticAveria Vibracion Excesiva Localización y reparación De averíasAveria LA Sierra no Arranca Averia no SE Puede Hacer UN Corte EN Angulo RectoFollow Steps Suivez LES Étapes Siga LOS Pasos Comme indiqué ci-dessus, et fixez-le avec du ruban adhésifPage Limited Warranty of Bosch Portable and Benchtop Power Tools

4100DG, 4100-09, 4100 specifications

Bosch Appliances 4100, 4100-09, and 4100DG are a series of highly regarded kitchen appliances designed to enhance efficiency and performance in home cooking. Bosch has a long-standing reputation for crafting high-quality products, and this series is no exception. Each model combines cutting-edge technology with sleek design to meet the needs of modern households.

A standout feature of the Bosch 4100 series is its powerful performance. These appliances come equipped with high-performance motors and advanced cooking capabilities that ensure consistent results. Whether baking, broiling, or roasting, users can expect even heat distribution and precise temperature control, which are critical for achieving culinary perfection.

The 4100 appliances also emphasize intuitive usability, featuring easy-to-navigate controls and thoughtful design. The models include user-friendly digital displays and simple button interfaces, making it easy for anyone, regardless of cooking experience, to operate them seamlessly. Additionally, the Bosch 4100 series is designed with a focus on safety, incorporating advanced systems that prevent overheating and ensure secure operation.

In terms of design, the Bosch 4100 models boast a streamlined aesthetic that blends well with any kitchen décor. Constructed from high-quality materials, they offer durability while exuding a modern, sophisticated look. The stainless-steel finishes not only add elegance but are also easy to clean and maintain, making them practical for everyday use.

Another noteworthy characteristic of the Bosch 4100 series is the energy efficiency standards they meet. These appliances are designed to utilize less energy without compromising performance, helping homeowners save on utility bills while minimizing their environmental footprint.

The 4100DG model specifically stands out for its dual-fuel capabilities, allowing users to harness the benefits of both gas and electric cooking methods. This versatility provides chefs with greater flexibility and precision, accommodating a variety of cooking styles and preferences.

Overall, Bosch Appliances 4100, 4100-09, and 4100DG exemplify craftsmanship and innovation in the kitchen appliance sector. Their combination of advanced technology, user-friendly features, and stylish designs make them an excellent choice for anyone looking to elevate their cooking experience and enhance their kitchen functionality.
Top Page Image Contents