Black & Decker SCS600 instruction manual Specific Safety Rules

Page 3

 

 

tool. Carrying power tools with your finger on the switch or energizing power tools

 

 

that have the switch on invites accidents.

 

d) Remove any adjusting key or wrench before turning the power tool on. A wrench

 

 

or a key left attached to a rotating part of the power tool may result in personal injury.

 

e) Do not overreach. Keep proper footing and balance at all times. This enables

 

f)

better control of the power tool in unexpected situations.

 

Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing

 

 

and gloves away from moving parts. Loose clothes, jewelry or long hair can be

 

 

caught in moving parts.

 

g) If devices are provided for the connection of dust extraction and collection

 

 

facilities, ensure these are connected and properly used. Use of dust collection

 

 

can reduce dust-related hazards.

4) Power tool use and care

 

a) Do not force the power tool. Use the correct power tool for your application.

 

 

The correct power tool will do the job better and safer at the rate for which it was

 

 

designed.

 

b) Do not use the power tool if the switch does not turn it on and off. Any power

 

 

tool that cannot be controlled with the switch is dangerous and must be repaired.

 

c) Disconnect the plug from the power source and/or the battery pack from the

 

 

power tool before making any adjustments, changing accessories, or storing

 

 

power tools. Such preventive safety measures reduce the risk of starting the power

 

 

tool accidentally.

 

d) Store idle power tools out of the reach of children and do not allow persons

 

 

unfamiliar with the power tool or these instructions to operate the power tool.

 

 

Power tools are dangerous in the hands of untrained users.

 

e) Maintain power tools. Check for misalignment or binding of moving parts,

 

 

breakage of parts and any other condition that may affect the power toolʼs

 

 

operation. If damaged, have the power tool repaired before use. Many accidents

 

f)

are caused by poorly maintained power tools.

 

Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp

 

 

cutting edges are less likely to bind and are easier to control.

 

g) Use the power tool, accessories and tool bits etc., in accordance with these

 

 

instructions, taking into account the working conditions and the work to be

 

 

performed. Use of the power tool for operations different from those intended could

 

 

result in a hazardous situation.

5) Service

 

a) Have your power tool serviced by a qualified repair person using only identical

 

 

replacement parts. This will ensure that the safety of the power tool is maintained.

wh

SPECIFIC SAFETY RULES

re the cutting tool may contact hidden wiring or its own cord. Contact with a

Hold power tools by insulated gripping surfaces when performing a operation

"live" wire will make exposed metal parts of the tool "live" and shockthe operator.

st

b platform. Holding the work by hand or against your body leaves itunstable and

Use clamps or an ther practical way to secure and s pp rt the workpiece to a

may lead to loss of control.

Keep hands away from cutting area. Never reach underneath the materialfor any

 

reason. Hold front of saw by grasping the contoured gripping area. Do not insert fingers or

 

thumb into the vicinity of the reciprocating blade and blade clamp. Donot stabilize the

saw by gripping the shoe.

Keep blades sharp. Dull blades may cause the saw to swerve or stall under pressure.

When cutting pipe or conduit ensure that they are free from water, electrical wiring, etc.

kerf (the slot created by cutting). A moving blade may impact the workpiece causing a

Allow the motor to come to a complete stop before withdrawing the blade from the

broken blade, workpiece damage or ossl of control and possible personal injury.

saw may slip and the blade could contact the body causing injury.

Never hold work in your hand, lap or against parts of your body when sawing.The

Keep handles dry, clean, free from oil and grease. This will enablebetter control ofthe

tool.

Clean out your tool often, especially after he vy use. Dust and grit containing metal

 

particles oftenaccumulate on interior surfaces and could create an electricshock hazard.

 

 

3

Image 3
Contents ACCU-TRAK Sawtm Safety Guidelines Definitions General Power Tool Safety WarningsWork area safety Specific Safety Rules Serious and ermanent respir These chemicals areVariable Speed Control Switching on and OFF Figure BBlade Installation and Removal To Install Ablade Figure CUse the appropriate blade for material being cut Smart Select Dial Figures D1, D2 & EChanging the Smart Select Dial Figure E 10-12 No 14-24 No 10-12 YesHolding the SAW Figure Ffigure F Blade StorageTo Open the Storage Door Figure G Possible Solution MaintenanceTroubleshooting Problem Possible CauseSee ‘Tools-Electric’ AccessoriesService Information Full TWO-YEAR Home USE Warranty For Service & SalesMode D’EMPLOI LES Outils Électriques Utilisation et entretien d’un outil électrique Sécurité personnelleRègles DE Sécurité Spécifiques Toujours Porter UN Équipement DE Protection Homologué Commande DE LA Vitesse Variable Installation ET Dépose DE LA LameMise EN Marche ET Arrêt Figure B Actionnement DU Cadran Smart Select Figure E Pour Retirer UNE LameUtiliser la bonne lame pour le matériau à couper Cadran Smart Select Figures D1, D2 ET E10-12 oui Oui Coupes droites Dans les Matériaux de Bois seulementTenir LA Scie Figure Ffigure F Rangement DES LamesOuverture DE Laportedu Compartiment DE Rangement Entretien Problème Cause possible Solution possibleConseils Pratiques Pour UN Usage Optimal Coupe d métalInformation SUR LES Réparations AccessoiresManual DE Instrucciones Pautas DE SEGURIDAD/DEFINICIONES Seguridad en el área de trabajoRiesgobordesdeafiladosdescargao piezaseléctricamóviles Seguridad personal Normas DE Seguridad Específicas Símbolos Instalacióny Extracción Dela Hoja FuncionamientoEncendido Y Apagado Figura B Control DE Velocidad VariableCambio DEL Dial Smart Select Para Quitar UNA HojaUtilice la hoja correcta para el material a cortar Dial Smart Select Figuras D1, D2 Y ECorte de ontornos/Curvas, rápida Artesanía Madera 10-12Media RápidaSostenimiento DE LA Sierra Figura F Compartimiento Para HojasPara Abrir LA Puertadel Compartimiento Figura G Aserrado en metal Detección DE ProblemasProblema Causa posible Solución posible Aserrado de maderaAccesorios Esta Garantia no Aplica Cuando Años DE GarantiaPara Servicio y ventas Solamente Para Propositos DE MexicoPage Cat No. SCS600