Gas Connection Requirements

Gas Conversion:

No attempt shall be made to convert the Power™ burner from the gas specified on the model/serial rating plate for use with a different gas type without consulting the serving gas supplier. The conversion kits supplied with the Power™ burner must be used. See “Gas Conversions” section for instructions.

Gas Pressure Regulator

The gas pressure regulator supplied with this Power™ burner must be used. The inlet (supply) pressure to the regulator should be as follows for proper operation:

LP Gas:

Set pressure: 11" (28 cm) WCP

Inlet (supply) pressure: 11" to 14" (28 cm to 35.5 cm) WCP

Natural Gas:

Set pressure: 4" (10.2 cm) WCP

Inlet (supply) pressure: 7" to 14" (17.8 cm to 35.5 cm) WCP maximum.

Contact local gas supplier if you are not sure about the inlet (supply) pressure.

Burner Requirements for High Altitude

Input ratings shown on the model/serial rating plate are for elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a rate of 4% for each 1,000 ft (304.8 m) above sea level. Orifice conversion is required. See “Assistance or Service” section to order.

Gas Supply Line Pressure Testing

Testing above ½ psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge):

The Power™ burner and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures greater than ½ psi (3.5 kPa).

Testing below ½ psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge) or lower:

The Power™ burner must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than ½ psi (3.5 kPa).

20 lb LP Gas Fuel Tank

This Power™ burner is equipped for use with a 20 lb LP gas fuel tank (fuel tank not supplied). A gas pressure regulator/hose assembly is supplied.

It is also design-certified by CSA International for local LP gas supply or for Natural gas with appropriate conversion.

A. Gas pressure regulator/hose assembly

The 20 lb LP gas fuel tank must be mounted and secured.

Door Style Tank Tray

1.Open cabinet doors.

2.Pull out the tank tray.

Tank tray

3.Place the 20 lb LP gas fuel tank bottom collar into the mounting hole in the tank tray.

4.Tighten the locking screw against the bottom collar of the 20 lb LP gas fuel tank to secure.

A.Locking screw

B.Mounting hole

C.Bottom collar

5.Slide tank tray back into the cabinet.

6.Close cabinet doors.

Local LP Gas Supply Conversion

Conversion must be made by a qualified gas technician. The qualified gas technician shall provide the gas supply to the selected Power™ burner location in accordance with the National Fuel Gas Code ANSI Z223.1/NFPA 54 - latest edition, and local codes. For conversion to local LP, the convertible regulator in the conversion kit supplied with the Power™ burner must be used.

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 - latest edition. The qualified LP gas technician shall provide the LP gas supply to the selected Power™ burner location in accordance with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 and local codes.

Follow instructions for converting to local LP gas in the “Gas Conversions” section.

A. New CSA International approved “outdoor” flexible gas supply line

B. Rear of Power™ burner C. To local LP gas supply

KBPU182VSS specifications

The KitchenAid KBPU182VSS is a standout appliance that perfectly combines style and functionality for modern kitchens. This built-in refrigerator is designed to enhance the food storage experience, offering a range of features that cater to performance and aesthetics alike.

One of the most notable features of the KBPU182VSS is its spacious interior, with a capacity of 18 cubic feet, which allows ample room for groceries, leftovers, and culinary ingredients. The stainless steel finish adds a sleek and contemporary look, making it a perfect fit for various kitchen designs. This model seamlessly integrates into cabinetry, ensuring a polished and cohesive kitchen appearance.

The refrigerator is equipped with the advanced FreshSeal technology that helps to keep food fresher for longer. This is achieved through enhanced cooling capabilities that maintain consistent temperatures. The cooling system utilizes a dual evaporator, which is essential for optimal humidity control. This feature prevents odor mixing between the fridge and freezer, ensuring that everything—from meats to fruits—remains flavorful and fresh.

Organization is another key aspect of the KBPU182VSS. It features adjustable shelves that allow users to customize the interior layout according to their storage needs. The produce drawers are specifically designed to maintain ideal humidity levels for fruits and vegetables, prolonging their freshness. Additionally, the model comes with specialized storage for beverages, dairy, and other commonly used items, promoting convenience in access.

One innovative feature is the vibrant LED lighting that illuminates the interior, making it easy to find items quickly, even in low-light conditions. The door bins are designed for easy access and can accommodate larger bottles and containers, proving to be a practical solution for busy households.

The KitchenAid KBPU182VSS also boasts energy-efficient technology, reducing its environmental impact while keeping energy bills low. This is in line with KitchenAid's commitment to sustainability, giving customers peace of mind regarding their energy consumption.

In summary, the KitchenAid KBPU182VSS perfectly melds style, functionality, and technology, making it an excellent choice for anyone looking to upgrade their kitchen. Its thoughtful design features, advanced cooling technologies, and organization options set it apart in the competitive market of built-in refrigerators, satisfying both aesthetic and practical needs.