Check and Adjust the Burners

7.Use a 7 mm socket and wrench or 7 mm nut driver to install the new 2.01 mm (inner burner) and 2.87 mm (outer burner) brass orifices supplied with this kit.

NOTE: The number 2.01 and 2.87 are stamped on the orifices for identification.

8.Replace the burner base. Insure the locator pin locks into the locator hole.

A. Locator pin

9.Replace outer burner top ring, locate with the igniter slot over the igniter.

A.Igniter

10.Replace inner burner top ring.

11.Replace the wok ring, locate the tabs to the slots and twist clockwise to secure.

12.Replace burner grate.

Hook up to Natural gas and Leak Test

1.Use pipe wrench to connect certified ¹⁄₂" (1.3 cm) gas supply pipe to inlet side of regulator from Natural gas supply according to local codes requirements. Use pipe thread sealant that is certified for use with LP gas at connections where required. There must be a certified manual shutoff valve in the gas supply line near the grill for easy access.

2.Turn on the gas supply to the grill.

3.Test all connections using an approved noncorrosive leak- detection solution. Bubbles will show a leak. Correct any leak found.

Record Conversion

1.The appliance nameplate is located on the right-hand side panel. With a permanent marker, check the box next to “Natural gas” and mark through “LP - Propane.”

In the last page of the Use and Care Guide, write “Converted to Natural Gas.” Also record the conversion date and the technician/company that performed the conversion.

NOTE: Place LP gas parts in plastic parts bag for future use and keep with pack containing literature.

The burners are tested and factory-set for most efficient operation. However, variations in gas supply and other conditions may make minor adjustments to low flame setting necessary.

It is recommended that a qualified person make burner adjustments.

A.4" (10.2 cm) for outer burner when set to “HI.”

B.3" (7.6 cm) for inner burner when set to HI.”

Low Flame Adjustment

If flame goes out on the “LO” setting, the low flame setting must be adjusted.

1.Turn off the valve and wait until burners are cool.

2.Light Power™ burner using information in the “Outdoor Power™ Burner Use” section.

3.Turn burner to its lowest setting and remove knob.

4.Hold valve stem with pliers and insert a small flat-blade screwdriver into the shaft.

5.Watch the flame and slowly turn the screwdriver counterclockwise.

6.Adjust flame to minimum stable flame.

A. Valve stem

B.Small flat-blade screwdriver

C.Pliers

7.Replace the control knob and turn off the burner.

8.Repeat steps 3 through 7 for each burner if needed.

KBPU182VSS specifications

The KitchenAid KBPU182VSS is a standout appliance that perfectly combines style and functionality for modern kitchens. This built-in refrigerator is designed to enhance the food storage experience, offering a range of features that cater to performance and aesthetics alike.

One of the most notable features of the KBPU182VSS is its spacious interior, with a capacity of 18 cubic feet, which allows ample room for groceries, leftovers, and culinary ingredients. The stainless steel finish adds a sleek and contemporary look, making it a perfect fit for various kitchen designs. This model seamlessly integrates into cabinetry, ensuring a polished and cohesive kitchen appearance.

The refrigerator is equipped with the advanced FreshSeal technology that helps to keep food fresher for longer. This is achieved through enhanced cooling capabilities that maintain consistent temperatures. The cooling system utilizes a dual evaporator, which is essential for optimal humidity control. This feature prevents odor mixing between the fridge and freezer, ensuring that everything—from meats to fruits—remains flavorful and fresh.

Organization is another key aspect of the KBPU182VSS. It features adjustable shelves that allow users to customize the interior layout according to their storage needs. The produce drawers are specifically designed to maintain ideal humidity levels for fruits and vegetables, prolonging their freshness. Additionally, the model comes with specialized storage for beverages, dairy, and other commonly used items, promoting convenience in access.

One innovative feature is the vibrant LED lighting that illuminates the interior, making it easy to find items quickly, even in low-light conditions. The door bins are designed for easy access and can accommodate larger bottles and containers, proving to be a practical solution for busy households.

The KitchenAid KBPU182VSS also boasts energy-efficient technology, reducing its environmental impact while keeping energy bills low. This is in line with KitchenAid's commitment to sustainability, giving customers peace of mind regarding their energy consumption.

In summary, the KitchenAid KBPU182VSS perfectly melds style, functionality, and technology, making it an excellent choice for anyone looking to upgrade their kitchen. Its thoughtful design features, advanced cooling technologies, and organization options set it apart in the competitive market of built-in refrigerators, satisfying both aesthetic and practical needs.