KitchenAid KBPU182VSS installation instructions Gas Connection to Natural Gas or Local LP Gas

Page 13

To Install the 20 lb LP Gas Fuel Tank:

1.Open cabinet doors.

2.Pull out the tank tray.

Tank tray

3.Place the 20 lb LP gas fuel tank bottom collar into the mounting hole in the tank tray.

4.Tighten the locking screw against the bottom collar of the 20 lb LP gas fuel tank to secure.

A

BC

A.Locking screw

B.Mounting hole

C.Bottom collar

5.Screw the gas pressure regulator/hose assembly to the 20 lb LP gas fuel tank as shown. (To disconnect, turn off the gas supply to the 20 lb LP gas fuel tank, then unscrew the gas pressure regulator/hose assembly from the 20 lb LP gas fuel tank as shown.)

connect

disconnectB

A

A. 20 lb LP gas fuel tank

B. Gas pressure regulator/hose assembly

6.Turn on the gas supply. Wait a few minutes for gas to move through the gas line.

7.Test all connections by brushing on an approved noncorrosive leak-detection solution. Bubbles will show a leak. Correct any leak found.

8.Slide tank tray back into the cabinet.

9.Go to “Plug in Power™ Burner” in this section.

Gas Connection to Natural Gas or Local LP Gas

WARNING

Explosion Hazard

Use a new CSA International approved “outdoor” gas supply line.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure gas pressure does not exceed 11” (28 cm) water column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

This installation must conform with local codes and ordinances. In the absence of local codes, installations must conform with either the National Fuel Gas Code ANSI Z223.1 - latest edition, or CAN/CGA-B149.1 Natural Gas and Propane installation code.

Copies of the standards listed above may be obtained from:

CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

National Fire Protection Association

One Batterymarch Park

Quincy, Massachusetts 02269

1.Make gas connections.

A combination of pipe fittings must be used to connect the Power™ burner to the existing gas line.

If local codes permit, use an outdoor flexible stainless steel tubing gas connector, design-certified by CSA International, to connect the Power™ burner to the rigid gas supply line. A ⁵⁄₈" diameter line is recommended. Using a wrench to tighten, connect the gas supply to the Power™ burner. Use pipe-joint compound on all non- flared male threads. Do not kink or damage the flexible connector when moving the Power™ burner.

Pipe-joint compounds suitable for use with LP gas must be used. Do not use TEFLON®† tape.

A

B

C

A. New CSA International approved “outdoor” flexible gas supply line

B. Rear of Power™ burner

C. To Natural gas or local LP gas supply

†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

13

Image 13
Contents Outdoor BUILT-IN Power Burner Your safety and the safety of others are very important Outdoor BUILT-IN Power Burner SafetyQuincy, Massachusetts Cleveland, Ohio Important Safety InstructionsTable DES Matières Table of ContentsProduct Dimensions Installation RequirementsTools and Parts Location RequirementsMaker Ice Cabinet Dimensions= 3 7.6 cm Between a Trash Drawer, Utility Drawer, or Warming Drawer19³⁄₈ 49.2 cm 10¾ 27.3 cm 19¾ 50.2 cm 13½ 34.3 cm 10⁵⁄₈ 27.0 cm 22¹¹⁄₁₆ 57.6 cm30½ 77.5 cm 10¾ 27.3 cm 23 58.4 cm Built-in Outdoor Grill Enclosure Ventilation for LP GasGas Supply Requirements Electrical RequirementsRecommended Ground Method Gas Connection Requirements Install Tank Tray for 20 lb LP Gas Fuel Tank Installation InstructionsNatural Gas Conversion Make Gas Connection Gas Connection to Natural Gas or Local LP Gas To Install the 20 lb LP Gas Fuel TankAssemble Cooking Area Plug in Power BurnerLift off cover and grate and set aside GAS Conversions Installation of the regulatorTools and Parts for Gas Conversion Conversion to a Local LP Gas SupplyConversion from LP Gas to Natural Gas Make Power Burner Connections Connect Local LP Gas SupplyRecord Conversion Reinstall cap onto convertible regulator Change the Power burner orificesLow Flame Adjustment Check and Adjust the BurnersHook up to Natural gas and Leak Test Power Burner Use Using Your Outdoor Power BurnerManually lighting the Power burner Lighting Your Power BurnerRemove the outdoor Power burner cover General Cleaning Outdoor Power Burner CareCleaning Method Do not soak knobsAssistance or Service TroubleshootingAccessories U.S.AThis limited warranty does not cover Kitchenaid Outdoor Product WarrantyCall Page Votre sécurité et celle des autres est très importante Sécurité DU Brûleur Dextérieur Encastré PowerConservez CES Instructions Dimensions du produit Exigences DinstallationExigences demplacement Dimensions du placardPlan = 3 7,6 cm Dimension C Dimension D Dimension E19³⁄₈ 49,2 cm 10¾ 27,3 cm 19¾ 50,2 cm 13½ 34,3 cm 10⁵⁄₈ 27 cm 22¹¹⁄₁₆ 57,6 cm30½ 77,5 cm 10¾ 27,3 cm 23 58,4 cm Taille de la porte Dimension F Dimension LSpécifications électriques Méthode recommandée de mise à la terreSpécifications de lalimentation en gaz Détendeur Exigences concernant le raccordement au gazBouteille de propane de 20 lb Puissance thermique des brûleurs en altitudeInstallation du brûleur dextérieur Encastré Power Instructions ’INSTALLATIONConversion pour lalimentation au gaz naturel Installation du chariot de bouteille de gaz propane de 20 lb Raccordement de gaz Installation de la bouteille de propane de 20 lbRaccordement à une bouteille de gaz propane de 20 lb Alimentation au gaz naturel ou au gaz propane local Branchement du brûleur PowerSoulever le couvercle et la grille et les mettre de côté Installation de la surface de cuissonConversions DE GAZ Installation du détendeurOutillage et pièces pour la conversion de gaz Conversion au gaz propane localEnregistrer la conversion Conversion du gaz propane au gaz naturel11. Réinstaller le chapeau sur le détendeur convertible Remplacement des gicleurs du brûleur PowerEnlever la grille du brûleur Power 12. Réinstaller la grille de brûleur 10. Réinstaller le cerclage supérieur du brûleur interneContrôle et réglage des brûleurs Raccordement au gaz naturel et recherche de fuitesUtilisation du brûleur Power Utilisation DU Brûleur Power DextérieurAllumage manuel du brûleur Power Allumage du brûleur PowerPlacer le wok sur le cerclage de wok Nettoyage général Entretien DU Brûleur Power DextérieurMéthode de nettoyage Détergent doux, chiffon doux et eau tiède Rincer et sécherAccessoires Assistance OU ServiceDépannage Au CanadaLa présente garantie limitée ne couvre pas Garantie DES Produits Pour Usage Extérieur KitchenaidComposer le 1-800-422-1230. Au Canada, composer le Page All rights reserved W10243318B

KBPU182VSS specifications

The KitchenAid KBPU182VSS is a standout appliance that perfectly combines style and functionality for modern kitchens. This built-in refrigerator is designed to enhance the food storage experience, offering a range of features that cater to performance and aesthetics alike.

One of the most notable features of the KBPU182VSS is its spacious interior, with a capacity of 18 cubic feet, which allows ample room for groceries, leftovers, and culinary ingredients. The stainless steel finish adds a sleek and contemporary look, making it a perfect fit for various kitchen designs. This model seamlessly integrates into cabinetry, ensuring a polished and cohesive kitchen appearance.

The refrigerator is equipped with the advanced FreshSeal technology that helps to keep food fresher for longer. This is achieved through enhanced cooling capabilities that maintain consistent temperatures. The cooling system utilizes a dual evaporator, which is essential for optimal humidity control. This feature prevents odor mixing between the fridge and freezer, ensuring that everything—from meats to fruits—remains flavorful and fresh.

Organization is another key aspect of the KBPU182VSS. It features adjustable shelves that allow users to customize the interior layout according to their storage needs. The produce drawers are specifically designed to maintain ideal humidity levels for fruits and vegetables, prolonging their freshness. Additionally, the model comes with specialized storage for beverages, dairy, and other commonly used items, promoting convenience in access.

One innovative feature is the vibrant LED lighting that illuminates the interior, making it easy to find items quickly, even in low-light conditions. The door bins are designed for easy access and can accommodate larger bottles and containers, proving to be a practical solution for busy households.

The KitchenAid KBPU182VSS also boasts energy-efficient technology, reducing its environmental impact while keeping energy bills low. This is in line with KitchenAid's commitment to sustainability, giving customers peace of mind regarding their energy consumption.

In summary, the KitchenAid KBPU182VSS perfectly melds style, functionality, and technology, making it an excellent choice for anyone looking to upgrade their kitchen. Its thoughtful design features, advanced cooling technologies, and organization options set it apart in the competitive market of built-in refrigerators, satisfying both aesthetic and practical needs.