Troubleshooting
| Problem | Cause |
| Solution | |
|
|
|
|
|
|
|
|
|
|
|
|
ProShot sprays with poor | Tip is partially clogged | See Unclogging Tip/Guard Assembly, page | |||
results |
| 12. |
| ||
|
|
|
|
|
|
|
|
| Tip is not in correct position | Rotate tip to SPRAY position. | |
|
|
|
|
|
|
|
|
| Incorrect tip for application of | See Reversible Tip Selection Chart, page 11. | |
|
|
| material. |
|
|
|
|
|
|
|
|
|
|
| Tip filter is partially clogged | Clean or replace filter. See page 12. | |
|
|
|
|
|
|
|
|
| Suction Tube screen is partially | Clean or replace Suction Tube. See page 13. | |
|
|
| clogged. |
|
|
|
|
|
|
|
|
|
|
| Fine Finish Optimizer is partially | Clean or replace Fine Finish Optimizer. See | |
|
|
| clogged. | page 9. | |
|
|
|
|
|
|
|
|
| Fine Finish Optimizer is installed while | Make sure compatible material is being used. | |
|
|
| using an incompatible material. | See Reversible Tip Selection Chart, page 11. | |
|
|
|
|
|
|
|
|
| Tip is worn or damaged | Replace tip. See Install Tip/Guard Assembly, | |
|
|
|
| page 11. | |
|
|
|
|
|
|
|
|
| Inlet or Outlet Valves are worn. | See ProShot Repair, page 17. | |
|
|
|
|
|
|
Paint leaks from sprayer trig- | Sprayer has reached its maximum life. | Replace sprayer. | |||
ger area. |
|
|
| ||
|
|
|
|
|
|
Battery is discharged but | Damaged battery. | Replace battery. | |||
charger still displays green |
|
|
| ||
light when battery is inserted. |
|
|
| ||
|
|
|
|
|
|
Spray Pattern Diagnostics |
|
| |||
|
|
|
|
|
|
| Problem | Cause |
| Solution | |
|
|
|
|
| |
|
|
|
|
| |
Spray pattern is pulsating: | Fine Finish Optimizer is installed while using | Make sure material is compatible. See | |||
|
|
| an incompatible material. |
| Reversible Tip Selection Chart, page 11. |
|
|
| Operator is moving too fast while spraying. | Slow speed of movement. | |
|
|
|
|
| |
Spray pattern has tails: | Fine Finish Optimizer is installed while using | Make sure compatible material is being used. | |||
|
|
| an incompatible material. |
| See Reversible Tip Selection Chart, page |
|
|
|
|
| 11. |
|
|
| Fine Finish Optimizer is partially clogged. | Clean or replace Fine Finish Optimizer. | |
|
|
|
|
| See page 9. |
|
|
| Material not compatible with sprayer. |
| Switch material. |
|
|
| Inlet or Outlet Valves are worn. |
| See ProShot Repair, page 17. |
|
|
|
|
|
|
Spray pattern has dripping: | Sprayer is moving too slow for material. |
| Move sprayer faster while spraying. | ||
|
|
| Sprayer is too close to target surface. |
| Move sprayer away from surface (10 in). |
|
|
| Holding trigger while changing spray |
| Release trigger when changing directions. |
|
|
| direction. |
|
|
|
|
| Incorrect tip for application of |
| See Reversible Tip Selection Chart, page |
|
|
|
| ||
|
|
| material. |
| 11. |
|
|
| Tip is worn or damaged. |
| Replace tip. See Install Tip/Guard Assembly, |
|
|
|
|
| page 11. |
|
|
|
|
|
|
3A0153E | 21 |