Models
Contents
Models | . . . . . . . . . . . . | . . . . . . . . . . . | 2. . | Operation | 18 | |
Warnings | . . . . . . . . . . . . | . . . . . . . . . . . | 3. . | Pressure Relief Procedure | 18 | |
Selection Charts . . | . . . . . . . . . . . . | . . . . . . . . . . . | 6. . | Apply Fluid | 18 | |
Gun Selection . . | . . . . . . . . . . . . | . . . . . . . . . . . | 6. . | Daily Gun Care | 19 | |
Proper Needle/Nozzle Selection | . . . . . . . . . . . | 6. . | General System Maintenance | 20 | ||
Models With Manifolds | . . . . . . . . . . . | 7. . | Clean and Flush Gun | 20 | ||
Models Without Manifolds | . . . . . . . . . . . | 7. . | Troubleshooting | 22 | ||
Air Caps | . . . . . . . . . . . . | . . . . . . . . . . . | 8. . | Service | 24 | |
Sample Pattern Sizes and Shapes | 8. . | Disassembly | 24 | |||
Needle Assembly Identification . | . . . . . . . . . . . | 8. . | Reassembly | 25 | ||
Installation | . . . . . . . . . . . . | . . . . . . . . . . . | 10. | Parts | 26 | |
Ventilate Spray Booth | . . . . . . . . . . . | 10. | Repair Kits | 28 | ||
Configure Gun and Manifold . . . | . . . . . . . . . . . | 10. | Accessories | 28 | ||
Ground System . | . . . . . . . . . . . . | . . . . . . . . . . . | 11. | Dimensions | 29 | |
Mount Gun . . . . | . . . . . . . . . . . . | . . . . . . . . . . . | 12. | Mounting Hole Layouts | 30 | |
Setup | . . . . . . . . . . . . | . . . . . . . . . . . | 13. | Technical Data | 32 | |
Connect Air Line | . . . . . . . . . . . . | . . . . . . . . . . . | 13. | Air Flow | 34 | |
Connect Fluid Hose | . . . . . . . . . . . | 15. | Spray Pattern Test Report | 35 | ||
Flush Spray Gun | . . . . . . . . . . . . | . . . . . . . . . . . | 16. | Graco Standard Warranty | 36 | |
Position Air Cap | . . . . . . . . . . . . | . . . . . . . . . . . | 16. | Graco Information | 36 | |
Adjust Spray Pattern | . . . . . . . . . . . | 16. |
|
|
| |
Models |
|
|
|
|
|
|
|
|
|
|
|
| |
| Orifice Size | Models with | Models without |
|
| |
Spray Type | in. (mm) | Manifold** | Manifold |
|
|
|
|
|
|
|
|
|
|
Conventional | 0.028 (0.7) | 24B857 | 24B877 |
|
|
|
Conventional | 0.035 (0.9) | 24B858 | 24B878 |
|
|
|
Conventional | 0.043 (1.1) | 24B859 | 24B879 |
|
|
|
Conventional | 0.051 (1.3) | 24B860 | 24B880 |
|
|
|
Conventional | 0.059 (1.5) | 24B861* |
|
|
| |
HVLP | 0.020 (0.5) | 24B862 |
|
|
| |
HVLP | 0.028 (0.7) | 24B863 | 24B881 |
|
|
|
HVLP | 0.043 (1.1) | 24B864 | 24B882 |
|
|
|
HVLP | 0.051 (1.3) | 24B865 | 24B883 |
|
|
|
HiTEch | 0.028 (0.7) | 24B866 | 24B884 |
|
|
|
HiTEch | 0.039 (1.0) | 24B867* | 24B885* |
|
|
|
HiTEch | 0.059 (1.5) | 24B868* | 24B886* |
|
|
|
LVMP | 0.020 (0.5) | 24B869 | 24B887 |
|
|
|
LVMP | 0.028 (0.7) | 24B870 | 24B888 |
|
|
|
LVMP | 0.035 (0.9) | 24B871 | 24B889 |
|
|
|
LVMP | 0.043 (1.1) | 24B872 | 24B890 |
|
|
|
LVMP | 0.051 (1.3) | 24B873 | 24B891 |
|
|
|
LVMP | 0.059 (1.5) | 24B874* |
|
|
| |
Air Brush | 0.028 (0.7) | 24B875 | 24B892 |
|
|
|
Gun without needle, | N/A | 24B876 | 24B893 |
|
|
|
nozzle, or air cap |
|
|
|
|
|
|
*Needle tip and nozzle exit constructed from tungsten carbide.
**Models with manifold have fully stainless steel fluid passages.
2 | 313869B |