Graco Inc TI14428A, 313869B, TI14427A important safety instructions Technical Data, Triggering Speed

Page 32

Technical Data

Technical Data

Maximum working fluid pressure . . . . . . . . . . . . . . . . . . . . 100 psi (0.7 MPa, 7 bar) Maximum working air pressure . . . . . . . . . . . . . . . . . . . . . 100 psi (0.7 MPa, 7 bar) Maximum HVLP Inbound Air Pressure. . . . . . . . . . . . . . . . See chart on page 8.

Maximum Working Fluid Temperature . . . . . . . . . . . . . . . . 120° F (49° C)

Minimum Air Cylinder Actuation Pressure . . . . . . . . . . . . . 50 psi (0.34 MPa, 3.4 bar) Weight

with manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 lb (575 g) with no manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.6 lb (275 g)

Wetted Parts

Models 24B857-24B860, 24B862-24B865,Nylon, PTFE, Stainless Steel, Ultra 24B869-24B873, 24B875 . . . . . . . . . . . . . . . . . . . . . . . High Molecular Weight Polyethylene

Model 24B866. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PTFE, Stainless Steel, Ultra High

Molecular Weight Polyethylene

Models 24B867 and 24B868. . . . . . . . . . . . . . . . . . . . . PTFE, Stainless Steel, Ultra High Molecular Weight Polyethylene, tungsten carbide

Models 24B861 and 24B874. . . . . . . . . . . . . . . . . . . . . Nylon, PTFE, Stainless Steel, Ultra

High Molecular Weight Polyethylene,

Tungsten Carbide

Models 24B877-24B883, 24B887-24B892 . . . . . . . . . . Anodized Aluminum, Nylon, Stain-

less Steel, Ultra High Molecular

Weight Polyethylene

Models 24B885 and 24B886. . . . . . . . . . . . . . . . . . . . . Anodized Aluminum, Stainless Steel, Tungsten Carbide, Ultra High Molec- ular Weight Polyethylene

Model 24B884. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Anodized Aluminum, Stainless Steel,

Ultra High Molecular Weight

Polyethylene

Triggering Speed

These values apply to a new gun with a 12 ft. (3.6 m), 1/4 in. (6.3 mm) OD cylinder air line and a 0.043 in. nozzle. These values will vary slightly with use and with variations in equipment.

Cylinder Air

 

 

msec to fully

msec to fully

Pressure

Fluid Pressure

Air Pressure

psi (kPa, bar)

psi (kPa, bar)

psi (kPa, bar)

open

close

 

 

 

 

 

50 (0.35, 3.5)

50 (0.35, 3.5)

100 (0.7, 7.0)

48

84

 

 

 

 

 

32

313869B

Image 32
Contents Important Safety Instructions AirPro EFX Automatic Spray GunContents ModelsFire and Explosion Hazard Equipment Misuse Hazard Toxic Fluid or Fumes Hazard Proper Needle/Nozzle Selection Selection ChartsGun Selection Models With Manifolds Models Without ManifoldsSample Pattern Sizes and Shapes Needle Assembly IdentificationAir Caps 313869B Installation Ventilate Spray BoothConfigure Gun and Manifold Guns with ManifoldGround System Guns without ManifoldStationary Support Mount GunReciprocating Arm Rod Mount Setup Connect Air LineAir regulator Without Manifold Connect Fluid HoseWith Manifold Flush Spray Gun Adjust Spray Pattern Perform Pressure Relief Procedure,Position Air Cap Vertical Pattern Horizontal PatternSuggested Starting Settings Spray Fan Air Atomizing Air Fluid Pressure RegulatorPressure Relief Procedure OperationApply Fluid IncorrectDaily Gun Care Follow the Pressure Relief Procedure, General System MaintenanceClean and Flush Gun 313869B Troubleshooting WrongProblem Cause Solution Service DisassemblyReassembly Guns without Manifold PartsGuns with Manifold Parts in Common Additional Parts for Models with ManifoldAccessories Repair KitsDimensions Mounting Hole Layouts 44.7 mm M8 x 1.25 T 35 in .9 mm deep 24.1 mm Slot Technical Data Triggering SpeedSound Data ConventionalHiTEch Air BrushAir Flow Spray Pattern Test Report Spray Pattern Test ReportGraco Standard Warranty Graco Information