Bosch Power Tools 34618, 34614, 34612 Inserting Bits, Screwdriver BIT BIT Holder Removing Chuck

Page 10

BM 2609140392 11/06 12/4/06 8:25 AM Page 10

INSERTING BITS

Move reverse switch lever to the center “OFF” position. Remove battery pack and rotate the clutch ring to the drill bit symbol

“ ”. Rotate the chuck sleeve counter- clockwise viewing from chuck end, and open chuck to approximate drill bit diameter. Insert a clean bit up to the drill bit flutes for small bits, or as far as it will go for large bits. Close chuck by rotating the chuck sleeve clockwise and securely tighten by hand (Fig. 4).

!WARNING Do not use the power of the drill while grasping

chuck to loosen or tighten bit. Friction burn or hand injury is possible if attempting to grasp the spinning chuck.

FIG. 4	CHUCK SLEEVE

SCREWDRIVER

BIT

BIT HOLDER

SCREWDRIVER BIT

REMOVING CHUCK

Rotate the clutch ring to the drill bit

symbol “ ”. Open the chuck all the way, remove left-hand thread screw inside chuck by turning it clockwise (Fig. 5).

Insert the short arm of a 1/2" hex key wrench and close jaws on flats of wrench (Fig. 6). Strike long arm of wrench sharply

counterclockwise, remove wrench and unthread chuck from spindle.

INSTALLING CHUCK

Always keep the spindle threads, the threads of the chuck and securing screw free of debris. To install a chuck, reverse “removing the chuck” procedure.

FIG. 5

FIG. 6

CHUCK SLEEVE

RELEASING AND INSERTING BATTERY PACK

Release battery pack from tool by pressing on both sides of the battery release tabs and pull downwards. Before inserting battery pack, remove protective cap from battery pack (Fig. 7).

To insert battery, align battery and slide battery pack into tool until it locks into position. Do not force.

-10-

Image 10

Contents Read Before Using Electrical safety General Safety RulesWork area safety Personal safetyService Power tool use and careBattery tool use and care Power tools are dangerous in the hands of untrained usersSafety Rules for Cordless Drill/Drivers Prolonged useBattery Care Battery/ChargerExplode NICKEL-CADMIUM Batteries Battery DisposalNICKEL-METAL Hydride Batteries Symbols Gear Shifter Adjustable Clutch Functional Description and SpecificationsCordless Drill/Driver Operating Instructions Inserting Bits Installing ChuckChuck Sleeve Releasing and Inserting Battery Pack Screwdriver BIT BIT Holder Removing ChuckImportant Charging Notes Charger Charging Battery Pack 30 Minute Single BAY-BC130RED Light Green Light Cap, guards against terminal shorting Charging Battery Pack 30 Minute Dual BAY-BC230RED Light Protective CAP Indicator Light Charging Battery Pack 1 Hour ChargerBattery Pack Charger Guards against terminal shortingOperating Tips Drilling Masonry Wire BrushesDrilling Metal Sanding and PolishingAccessories MaintenanceCleaning Sécurité électrique Consignes générales de sécuritéSécurité du lieu de travail Sécurité personnelleUtilisation et entretien des outils à piles Utilisation et entretien des outils ÉlectroportatifsEntretien Ne faites pas fonctionner la perceuse en la portant Consignes de sécurité pour perceuses/tournevis sans cordonLe plomb provenant des peintures à base de plomb Entretien des piles Chargeur de pilePas dans l’outil ou le Piles NICKEL-CADMIUM Mise au rebut des pilesNe tentez pas de Piles NICKEL-HYDRURE DE MétalSymboles Perceuse/visseuse sans fil Description fonctionnelle et spécificationsChangement DE Vitesse Embrayage Réglable Changement DE Vitesses Consignes de fonctionnementLevier DE Marche AVANT/ARRIÈRE ET Verrouillage DE Gâchette FreinEmbout DE Tournevis PORTE-MECHE Retrait DU Mandrin Insertion DES ForetsDe la perceuse en Pose DU MandrinRemarques Importantes Concernant LA Charge Fin dès que le bloc-piles est totalement chargé Chargé et ne reçoit qu’une charge de maintienVoyant Rouge Voyant Vert Pleinement chargé et ne reçoit qu’une charge de maintien Voyant Rouge Voyant Vert ChargeurPiles est totalement chargé Consignes de fonctionnement Ponçage ET Polissage Perçage DES MétauxPerçage DE LA Maçonnerie Brosses MétalliquesEntretien AccessoiresNettoyage Seguridad eléctrica Normas generales de seguridadSeguridad del área de trabajo Seguridad personalUso y cuidado de las herramientas Alimentadas por baterías MecánicasServicio de ajustes y reparaciones BM 2609140392 11/06 12/4/06 825 AM Batería/cargador Cuidado de las bateríasBaterías DE NIQUEL-CADMIO Eliminación de las bateríasBaterías DE NIQUEL-HIDRURO Metalico Con aislamiento doble SímbolosDe Ni-Cd Cambiador DE Engranajes Embrague Ajustable Descripción funcional y especificacionesTaladro/destornillador sin cordón Lengüetas DE Liberación DE LAS BateríasPalanca DE AVANCE/INVERSIÓN Y Cierre DEL Gatillo Instrucciones de funcionamientoInterruptor Gatillo DE Velocidad Variable Controlada Cambio DE EngranajesBroca Destornilladora Portabroca Desmontaje DEL Mandril Colocacion DE LAS BrocasInstalacion DEL Mandril Notas Importantes Para Cargar Cargador LUZ Roja LUZ VerdeDemasiado caliente o demasiado frío Cargador LUZ RojaTotalmente cargado Carga DEL Paquete DE Baterías Cargador DE 1 HoraEstá recibiendo energía del tomacorriente de Paquete DE Baterías CargadorBrocas Para Taladro Consejos de funcionamientoSujecion CON Tornillos Taladrado DE MaderaLijado Y Pulido Taladrado DE MetalTaladrado DE Mamposteria Escobillas DE AlambreServicio MantenimientoAccesorios LimpiezaBM 2609140392 11/06 12/4/06 825 AM Remarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools