Bosch Power Tools 34612, 34614, 34618 manual Maintenance, Accessories, Cleaning

Page 17

BM 2609140392 11/06 12/4/06 8:25 AM Page 17

Maintenance

Service

!WARNING NO USER SERVICEABLE PARTS INSIDE. Preventive

maintenance performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recom- mend that all tool service be performed by a Bosch Factory Service Center or Authorized Bosch Service Station. SERVICEMEN: Disconnect tool and/or charger from power source before servicing.

BATTERIES

Be alert for battery packs that are nearing their end of life. If you notice decreased tool performance or significantly shorter running time between charges then it is time to replace the battery pack. Failure to do so can cause the tool to operate improperly or damage the charger.

Long term battery storage should be in the discharged state. Battery packs last longer and re-charge better when they are stored discharged. Remember to fully re- charge battery packs before using after prolonged storage.

TOOL LUBRICATION

Your Bosch tool has been properly lubricated and is ready for use.

D.C. MOTORS

The motor in your tool has been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend it be examined every six months. Only a genuine Bosch replacement motor specially designed for your tool should be used.

Cleaning

!To avoid accidents, always WARNING disconnect the tool and/or

charger from the power supply before cleaning. The tool may be cleaned most effectively with compressed dry air. Always wear safety goggles when cleaning tools with compressed air.

Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through opening.

Certain cleaning agents ! CAUTION and solvents damage

plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia.

Accessories

!WARNING If an extension cord is necessary, a cord with

adequate size conductors that is capable of carrying the current necessary for your tool must be used. This will prevent excessive voltage drop, loss of power or overheating. Grounded tools must use 3-wire extension cords that have 3-prong plugs and receptacles.

NOTE: The smaller the gauge number, the heavier the cord.

RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT ALTERNATING CURRENT TOOLS

Tool’s

Cord Size in A.W.G.

Wire Sizes in mm2

Ampere

 

 

 

 

 

 

 

 

Cord Length in Feet

Cord Length in Meters

Rating

25

50

100

150

15

30

60

120

 

3-6

 

 

 

 

 

 

 

 

18

16

16

14

0.75

0.75

1.5

2.5

6-8

18

16

14

12

0.75

1.0

2.5

4.0

8-10

18

16

14

12

0.75

1.0

2.5

4.0

10-12

16

16

14

12

1.0

2.5

4.0

12-16

14

12

 

 

 

 

 

 

 

 

 

(* = standard equipment)

**

15 minute charger

(** = optional accessories)

** 30 minute charger (single bay)

*

Screwdriver bit

** 30 minute charger (dual bay)

*

Carrying case

**

1 hour charger

-17-

Image 17
Contents Read Before Using Work area safety General Safety RulesElectrical safety Personal safetyBattery tool use and care Power tool use and careService Power tools are dangerous in the hands of untrained usersProlonged use Safety Rules for Cordless Drill/DriversExplode Battery/ChargerBattery Care NICKEL-METAL Hydride Batteries Battery DisposalNICKEL-CADMIUM Batteries Symbols Cordless Drill/Driver Functional Description and SpecificationsGear Shifter Adjustable Clutch Operating Instructions Chuck Sleeve Releasing and Inserting Battery Pack Installing ChuckInserting Bits Screwdriver BIT BIT Holder Removing ChuckImportant Charging Notes RED Light Green Light Charging Battery Pack 30 Minute Single BAY-BC130Charger RED Light Charging Battery Pack 30 Minute Dual BAY-BC230Cap, guards against terminal shorting Battery Pack Charger Charging Battery Pack 1 Hour ChargerProtective CAP Indicator Light Guards against terminal shortingOperating Tips Drilling Metal Wire BrushesDrilling Masonry Sanding and PolishingCleaning MaintenanceAccessories Sécurité du lieu de travail Consignes générales de sécuritéSécurité électrique Sécurité personnelleEntretien Utilisation et entretien des outils ÉlectroportatifsUtilisation et entretien des outils à piles Le plomb provenant des peintures à base de plomb Consignes de sécurité pour perceuses/tournevis sans cordonNe faites pas fonctionner la perceuse en la portant Pas dans l’outil ou le Chargeur de pileEntretien des piles Ne tentez pas de Mise au rebut des pilesPiles NICKEL-CADMIUM Piles NICKEL-HYDRURE DE MétalSymboles Changement DE Vitesse Embrayage Réglable Description fonctionnelle et spécificationsPerceuse/visseuse sans fil Levier DE Marche AVANT/ARRIÈRE ET Verrouillage DE Gâchette Consignes de fonctionnementChangement DE Vitesses FreinDe la perceuse en Insertion DES ForetsEmbout DE Tournevis PORTE-MECHE Retrait DU Mandrin Pose DU MandrinRemarques Importantes Concernant LA Charge Voyant Rouge Voyant Vert Chargé et ne reçoit qu’une charge de maintienFin dès que le bloc-piles est totalement chargé Voyant Rouge Voyant Vert Chargeur Pleinement chargé et ne reçoit qu’une charge de maintienPiles est totalement chargé Consignes de fonctionnement Perçage DE LA Maçonnerie Perçage DES MétauxPonçage ET Polissage Brosses MétalliquesNettoyage AccessoiresEntretien Seguridad del área de trabajo Normas generales de seguridadSeguridad eléctrica Seguridad personalServicio de ajustes y reparaciones MecánicasUso y cuidado de las herramientas Alimentadas por baterías BM 2609140392 11/06 12/4/06 825 AM Cuidado de las baterías Batería/cargadorBaterías DE NIQUEL-HIDRURO Metalico Eliminación de las bateríasBaterías DE NIQUEL-CADMIO De Ni-Cd SímbolosCon aislamiento doble Taladro/destornillador sin cordón Descripción funcional y especificacionesCambiador DE Engranajes Embrague Ajustable Lengüetas DE Liberación DE LAS BateríasInterruptor Gatillo DE Velocidad Variable Controlada Instrucciones de funcionamientoPalanca DE AVANCE/INVERSIÓN Y Cierre DEL Gatillo Cambio DE EngranajesInstalacion DEL Mandril Colocacion DE LAS BrocasBroca Destornilladora Portabroca Desmontaje DEL Mandril Notas Importantes Para Cargar LUZ Roja LUZ Verde CargadorCargador LUZ Roja Demasiado caliente o demasiado fríoEstá recibiendo energía del tomacorriente de Carga DEL Paquete DE Baterías Cargador DE 1 HoraTotalmente cargado Paquete DE Baterías CargadorSujecion CON Tornillos Consejos de funcionamientoBrocas Para Taladro Taladrado DE MaderaTaladrado DE Mamposteria Taladrado DE MetalLijado Y Pulido Escobillas DE AlambreAccesorios MantenimientoServicio LimpiezaBM 2609140392 11/06 12/4/06 825 AM Remarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools