Bosch Power Tools 34612, 34614, 34618 manual Important Charging Notes

Page 11

BM 2609140392 11/06 12/4/06 8:25 AM Page 11

IMPORTANT CHARGING NOTES

1.The battery pack accepts only about 80% of its maximum capacity with its first few charge cycles. However, after the first few charge cycles, the battery will charge to full capacity.

2.The charger was designed to fast charge the battery only when the battery temperature is between 40˚F (4˚C) and 105˚F (41˚C).

3.A substantial drop in operating time per charge may mean that the battery pack is nearing the end of its life and should be replaced.

4.If you anticipate long periods (i.e. a month or more) of non-use of your tool, it is best to run your tool down until it is fully discharged before storing your battery pack. After a long period of storage, the capacity at first recharge will be lower. Normal capacity will be restored in two or three charge/discharge cycles.

Remember to unplug charger during storage period.

5.If battery does not charge properly:

a.Check for voltage at outlet by plugging in some other electrical device.

b.Check to see if outlet is connected to a light switch which turns power “off” when lights are turned off.

c.Check battery pack terminals for dirt. Clean with cotton swab and alcohol if necessary.

d.If you still do not get proper charging, take or send tool, battery pack and charger to your local Bosch Service Center. See “Tools, Electric” in the Yellow Pages for names and addresses.

Note: Use of chargers or battery packs not sold by Bosch will void the warranty.

-11-

Image 11
Contents Read Before Using Personal safety General Safety RulesWork area safety Electrical safetyPower tools are dangerous in the hands of untrained users Power tool use and careBattery tool use and care ServiceProlonged use Safety Rules for Cordless Drill/DriversExplode Battery/ChargerBattery Care NICKEL-METAL Hydride Batteries Battery DisposalNICKEL-CADMIUM Batteries Symbols Cordless Drill/Driver Functional Description and SpecificationsGear Shifter Adjustable Clutch Operating Instructions Screwdriver BIT BIT Holder Removing Chuck Installing ChuckChuck Sleeve Releasing and Inserting Battery Pack Inserting BitsImportant Charging Notes RED Light Green Light Charging Battery Pack 30 Minute Single BAY-BC130Charger RED Light Charging Battery Pack 30 Minute Dual BAY-BC230Cap, guards against terminal shorting Guards against terminal shorting Charging Battery Pack 1 Hour ChargerBattery Pack Charger Protective CAP Indicator LightOperating Tips Sanding and Polishing Wire BrushesDrilling Metal Drilling MasonryCleaning MaintenanceAccessories Sécurité personnelle Consignes générales de sécuritéSécurité du lieu de travail Sécurité électriqueEntretien Utilisation et entretien des outils ÉlectroportatifsUtilisation et entretien des outils à piles Le plomb provenant des peintures à base de plomb Consignes de sécurité pour perceuses/tournevis sans cordonNe faites pas fonctionner la perceuse en la portant Pas dans l’outil ou le Chargeur de pileEntretien des piles Piles NICKEL-HYDRURE DE Métal Mise au rebut des pilesNe tentez pas de Piles NICKEL-CADMIUMSymboles Changement DE Vitesse Embrayage Réglable Description fonctionnelle et spécificationsPerceuse/visseuse sans fil Frein Consignes de fonctionnementLevier DE Marche AVANT/ARRIÈRE ET Verrouillage DE Gâchette Changement DE VitessesPose DU Mandrin Insertion DES ForetsDe la perceuse en Embout DE Tournevis PORTE-MECHE Retrait DU MandrinRemarques Importantes Concernant LA Charge Voyant Rouge Voyant Vert Chargé et ne reçoit qu’une charge de maintienFin dès que le bloc-piles est totalement chargé Voyant Rouge Voyant Vert Chargeur Pleinement chargé et ne reçoit qu’une charge de maintienPiles est totalement chargé Consignes de fonctionnement Brosses Métalliques Perçage DES MétauxPerçage DE LA Maçonnerie Ponçage ET PolissageNettoyage AccessoiresEntretien Seguridad personal Normas generales de seguridadSeguridad del área de trabajo Seguridad eléctricaServicio de ajustes y reparaciones MecánicasUso y cuidado de las herramientas Alimentadas por baterías BM 2609140392 11/06 12/4/06 825 AM Cuidado de las baterías Batería/cargadorBaterías DE NIQUEL-HIDRURO Metalico Eliminación de las bateríasBaterías DE NIQUEL-CADMIO De Ni-Cd SímbolosCon aislamiento doble Lengüetas DE Liberación DE LAS Baterías Descripción funcional y especificacionesTaladro/destornillador sin cordón Cambiador DE Engranajes Embrague AjustableCambio DE Engranajes Instrucciones de funcionamientoInterruptor Gatillo DE Velocidad Variable Controlada Palanca DE AVANCE/INVERSIÓN Y Cierre DEL GatilloInstalacion DEL Mandril Colocacion DE LAS BrocasBroca Destornilladora Portabroca Desmontaje DEL Mandril Notas Importantes Para Cargar LUZ Roja LUZ Verde CargadorCargador LUZ Roja Demasiado caliente o demasiado fríoPaquete DE Baterías Cargador Carga DEL Paquete DE Baterías Cargador DE 1 HoraEstá recibiendo energía del tomacorriente de Totalmente cargadoTaladrado DE Madera Consejos de funcionamientoSujecion CON Tornillos Brocas Para TaladroEscobillas DE Alambre Taladrado DE MetalTaladrado DE Mamposteria Lijado Y PulidoLimpieza MantenimientoAccesorios ServicioBM 2609140392 11/06 12/4/06 825 AM Remarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools