Sears 113.206931 Check Motor Rotation, M, rotate COUNTERC.OCKWiSE whe, Direction, Flush Hereshaft

Page 10

osse mbb

i

:::shaft _th h_bl fi_,_ with

of Sh_t_ ioser'_ rn6tOr

CHECK MOTOR ROTATION

T_,_ m_ m_,_ rotate COUNTERC{.OCKWiSE whe_

Wewed fr_ PL_LL£Y end_

1L Piaee motor or_ your workbench or on floor.

2.Stared clear of motor and plug cord into a properly 9rounded outlet (See pa_¢ 5). f_}otice r_tation of pulley,

If it is not tutoring COUNTERCLOCKWISE, REMOVE

plug from out_et, and chancre rotation of motor accord-

ing to instructions furnished with motor.

WARNING: FOR YOUR OWN SAFETY, MAKE SLIRE

PLUG IS NOT CONNECTED TO POWER SOURCE OUT.

LET WHEN CHANG!NG ROTATION.

"_" --:--:-

; ;

__ ,

J__JLU'L_I_I'E..L '=!....

&CIJ_UU['L'....

MOUNTING MOTOR

i, Find fo_t 5116-t8 x 3/4" carriage bolts, flat washers, and lockw_sher and nuts_

2_ Attach r'_otor by iriserting carriage bolts through slots in motor' base and thro_Jgh slOtS in motor supporL Place a f}al washer, lo_.kwasher and nut on each carriage bolt,

:, b_t DO NOT TIGHTf_N nut.

">/:

/ECZ2"3

i i_ _

J

MOTOR MOUNT BRACKt_T

6.Install three clips on belt guard 90 ° apart with long tabs pointing AWAY from round opening.

7, Insert belt into open end of guard.

DIRECTION

OF

ROTATION

5t32 IN.

SETSCREW

WRENCH

MOTOR

FLUSH HERESHAFT

KEY

®

BELT

/

/•

1_..,_-"" BE LT O UAR D C LIPS

(90 _ APART)

10

Image 10

Contents JOINTER/PLANER only JOINTER/PLANER with Legs and MotorKnow Your Power Tool Make WOR Kshop KID-PROOFGetting To Know Your JOINTER-PLANER MaintenanceING KickbacksRepair Parts General SafetyAssembly RecommendedRemoving the Plug to or from the Outlet Connecting to Power Source OutletOutlet Checking contents Unpacking and checking contents Wrench CHECKING-CUTTER Blades and Screws32 IN. Setscrew 114-20TRUSS Side Stiffener Head Screw END Motor Support ATSliding Guard INSTALLINGMounting Switch Mounting Recommended Craftsman Motor and Belt GuardsDirection Check Motor RotationM, rotate COUNTERC.OCKWiSE whe Rotation3OINTER-PULLEYBELT Guard Installation HreJInfeed Slide 8RACKET Cutter Guard 6 ON-OFF Depth of CUT Sliding GUA RDOutfeedtable HandwheelFence Face Square tNFEEDCutter Guard Head Infeed Table END HighParallel condition Squaretable Fence Cutter GuardWood Your Work Bench Rotate Blade OUT WAY Penc LOutfeed Screwing in the studs will Raise the table Leveling StudsView Looking UP for Parts Identification Hazardous USE by ChildrenMotor Cord Power CordHold Planing Wood That is Thicker than 3 Feeding the WorkpieceJointing Wood That is Wider than 3 With the Grain Using the Hold DOWN!PUSH BlocksAgainst the Grain Follow Same When planing wood 3/4 in, thick and Narrower thanBEY Eling PlaningBlade Wedge Lifterlockscrew Screw Replacing Cutter BladesIiiiii!ii¸i Block of Wood Hold32 IN. Setscrew Wrench Cutte Setscrew Mark Slots 1, 2 IN, Setscf WrenchLifter Screw Lifter Wedge Lockslrew WedgePlace Guard Tang Spring Center Counter ClockwiseInfeed Pivot PINNever Rotate Sharpening Cutter BladesNEW Blade Spring Position aSpacer and Slide DovetailElevating Screw View Looking UP for Parts Identification Trouble ChartRecommended Accessories ShootingCraftsman 6-1/8iNCH JOINTER-PLANER Model No .206801 Hardware for Mounting Tool and MotorSee Fgure 5 for Exploded View Fence Assembly See for Exploded View3425 Craftsman 64/8 Inch JOINTER.PLANER Model No .206801 Key21 22 Key Part 113.206801 JOINTER!PLANER with Legs and Motor8 Inch JOINTER-PLANER