Sears 206801, 113.206931 manual Motor Cord, Hold, Power Cord

Page 17

b, To turn machine on, insert finger under switch lever and pull end of switch out.

c. To turn machine OFF... PUSH lever in.

Never leave machine unattended until it has come to a complete stop.

d. To lock switch in OFF position.., hold switch tN with one hand,. , REMOVE key with other hand.

WARNING: FOR YOUR OWN SAFETY, ALWAYS LOCK THE SWITCH "OFF" WHEN MACHINE IS

NOT tN USE . . . REMOVE KEY AND KEEPtT IN A SAFE PLACE ,.. ALSO ... IN THE EVENT OF A

POWER FAILURE (ALL OF YOUR LIGHTS GO OUT) TURN SWITCH OFF . . . AND REMOVE

THE KEY. THIS WILL PREVENT THE MACHINE FROM STARTING UP AGAIN WHEN THE POWER COMES BACK ON,

e, Plug motor cord into outlet in switch box.

WARNING: DON'T CONNECT POWER CORD TO

ELECTRICAL OUTLET IN YOUR SHOP UNTIL YOU ARE SURE THAT MOTOR ROTATION IS CORRECT. (SEE PAGE 10).

HOLD

PULL -.....

\

MOTOR

CORD

t

POWER

CORD

17

Image 17
Contents JOINTER/PLANER with Legs and Motor JOINTER/PLANER onlyMake WOR Kshop KID-PROOF Know Your Power ToolING MaintenanceGetting To Know Your JOINTER-PLANER KickbacksAssembly General SafetyRepair Parts RecommendedOutlet Connecting to Power Source OutletRemoving the Plug to or from the Outlet Checking contents Unpacking and checking contents 32 IN. Setscrew CHECKING-CUTTER Blades and ScrewsWrench 114-20TRUSS Side Stiffener Head Screw END Motor Support ATMounting Switch INSTALLINGSliding Guard Mounting Recommended Craftsman Motor and Belt GuardsM, rotate COUNTERC.OCKWiSE whe Check Motor RotationDirection RotationHreJ 3OINTER-PULLEYBELT Guard InstallationOutfeedtable Sliding GUA RDInfeed Slide 8RACKET Cutter Guard 6 ON-OFF Depth of CUT HandwheelCutter Guard Square tNFEEDFence Face Parallel condition Infeed Table END HighHead Squaretable Fence Cutter GuardOutfeed Rotate Blade OUT WAY Penc LWood Your Work Bench View Looking UP for Parts Identification Leveling StudsScrewing in the studs will Raise the table Hazardous USE by ChildrenHold Power CordMotor Cord Jointing Wood That is Wider than 3 Feeding the WorkpiecePlaning Wood That is Thicker than 3 Against the Grain Using the Hold DOWN!PUSH BlocksWith the Grain BEY Eling When planing wood 3/4 in, thick and Narrower thanFollow Same PlaningIiiiii!ii¸i Replacing Cutter BladesBlade Wedge Lifterlockscrew Screw Block of Wood HoldLifter Screw Cutte Setscrew Mark Slots 1, 2 IN, Setscf Wrench32 IN. Setscrew Wrench Lifter Wedge Lockslrew WedgeInfeed Counter ClockwisePlace Guard Tang Spring Center Pivot PINNEW Blade Sharpening Cutter BladesNever Rotate Spring Position aElevating Screw View Looking UP for Parts Identification DovetailSpacer and Slide Recommended Accessories ChartTrouble ShootingHardware for Mounting Tool and Motor Craftsman 6-1/8iNCH JOINTER-PLANER Model No .2068013425 Fence Assembly See for Exploded ViewSee Fgure 5 for Exploded View Key Craftsman 64/8 Inch JOINTER.PLANER Model No .20680121 22 Key Part 8 Inch JOINTER-PLANER JOINTER!PLANER with Legs and Motor113.206801