Sears 113.206931, 206801 manual Unpacking and checking contents

unpacking and checking contents

TABLE

OF

LOOSE

PARTS

The

Following

Parts

Are

included

With

Item

Model

113.206931

Only

No,

Description

Qty.

A

Leg

..............................

4

8

End Stiffener

.......................

2

C

Side

Stiffener

......................

4

D

Motor

Support

.....................

1

E

Motor

............................

1

Package of Miscellaneous Small Parts,

No. 67035, Consisting of the Following:

F

Cord

Clip

..........................

2

G

Hex

Nut,

1/4

in.

-

20

(approx.

die,

of

hole

1/4

in.)

..........

40

G

Hex

Nut,

5/I6

in. -

18

(approx.

alia. of

hole

5/1

6 in.)

.........

7

G

Hex

Nut,

1/2

in.

-

13

(approx.

die.

of

hole

1/2

in.)

..........

8

H

Truss

Hd,

Screw,

!/4

in.

-

20

x 5/'8 in.

long. (Top

of screw

is rounded)

........

40

J

Flat

Washer

(dia,

of

hole

11/32

in.)

......

7

K

Lockwasher,

1/4

in. External

Type

(approx.

dia.

of

hole

1/4

in.)

..........

40

K

Lockwasher,

5/1

6 in.

External

Type

(approx.

die.

of

hole

5/16

in,)

.........

7

L

Carriage

Boh,

5/16

in. -

18

x

3/4

long ...

3

M

Leveling

Foot

......................

4

N

Hex

Hd.

Screw,

5/16

in. -

18

x 2

in

3

=

JL

_

, LLUH,H,

C

A

F

JK

LM N

assembly

ASSEMBLING STEEL LEGS

NOTE: Steel Legs are furnished with Model 11 3.206931.

From among the loose parts, find the following Hardware:

40 Truss Head Screws, 1/4-20 x 5/8

40 Lockwashers, 1/4-External

40Hex Nuts, 1/4-20

8Hex Nuts, 1/2q3

4Leveling Feet

TRUSS HD. SCREW			END STIFFENER
1/4-2i	X 51//84EXTERNAL			1
END	\	LOCKWASHER	_
STIFFENER	!_	_//_ 1/4_20	HEX NUT	_"
			IDE	STIFFENERS

1.Assemble two (2) Side Stiffeners together using four (4)

1/4-20 Truss head screws, Iockwasher and nuts. Make two (2) Side Stiffener assemblies.

The End Stiffeners are placed on top and at each end of Side Stiffener assemb)ies as shown. Align holes, letter

coded "'B'" in Side Stiffeners and End Stiffeners and then insert 1/4-20 Truss head screws through the 9/32

diameter holes and install Iockwashers and nuts and then tighten.

2.Assemble the four (4) Legs to the Side and End Stiffeners using 1/4-20 screws, Iockwashers and nuts as shown,

3.Assemble the Motor Support to the Legs with 1/4,20

screws, ]ockwashers and nuts. Motor Support can be assembled to either end of Leg set.

4.Install leveling feet as shown. To )eve,] Leg Set, loosen nut on inside of leg and turn nut on the outside to raise or lower feet. Adjust all four leveling feet, if necessary, and then tighten nuts on the inside of leg.

NOTE: These levelers are not intended for height adius_ment,