Connecting to Power Source Outlet

motor specifications and emedrkaR requkernents :

This machine is designed to use a 3450 RPM motor only. Do not use any motor that runs faster than 3450 RPM.

It is wired for operation on 110-120 volts, 60 Hz.,a/ter-

nating current. IT MUST NOT BE CONVERTED TO

OPERATE ON 230 VOI.TS, EVEN THOUGH SOME OF

THE RECOMMENDED MOTORS ARE DUAL VOLTAGE.

THESE CRAFTSMAN MOTORS HAVE BEEN

FOUND TO BE ACCEPTABLE FOR USE ON THIS TOOL.

H P	RP_a	VOLTS	CATALOG	NO.
1/2	3450	110q20	1216
1/2	3450	110-120	1218
3/4	3450	110-120	12t9
3/4	3450	110-120	1226

CAUTION: Do not use blower or washing machine motors or any motor with an automatic reset overload protector

as their use may be hazardous.

This machine must be grounded while in use to protect the operator from etectric shock.

Plug power cord into a 110_120V properly grounded type

outlet protected by a 15-amp, dual element time delay or Circuit-Saver fuse or circuit breaker.

If you are not sure that your outlet is properly grounded, have it checked by a qualified electrician.

WARNING: DO NOT PERMIT FINGERS TO TOUCH

THE TERMINALS OF PLUGS WHEN INSTALLING OR

REMOVING THE PLUG TO OR FROM THE OUTLET.

WARNING: IF NOT PROPERLY GROUNDED THIS

POWER TOOL CAN INCUR THE POTENTIAL HAZARD

OF ELECTRICAL SHOCK. PARTICULARLY WHEN USED

IN DAMP LOCATIONS IN PROXIMITY TO PLUMBING.

IF AN ELECTRICAL SHOCK OCCURS THERE IS THE

POTENTIAL OF A SECONDARY HAZARD SUCH AS

YOUR HANDS CONTACTING THE CUTTING BLADE,

If power cord is worn or cut, or damaged in any way, have it replaced immediately.

3-PRONG PLUG

PROPERLY

GROUNDED

OUTLET_._

GROUNDING

PRONG

This power too! is equipped with a 3-conductor cord and grounding type plug wMch has a grounding prong listed by

Underwriters" Laboratories Association, The ground

conductor has a green jacket and is attached to the tool

housing at one end and to the ground prong in the

attachment plug at the other end.

This piug requires a mating 3-conductor grounded type outlet as shown.

If the outlet you are planning to use for this power too_ is

of the two prong type DO NOT REMOVE OR ALTER

THE GROUNDING PRONG IN ANY MANNER. Use an

adapter as shown and always connect the grounding lug to known ground,

It is recommended that you _nave a quafified electrician replace the TWO prong outlet with a properhi grounded THREE prong outlet,

An adapter as shown below is available for connecting plugs to 2-prong receptacles. The green grounding lug extending from the adapter must be connected to a perrnanent ground such as to a properly grounded outtet box.

MAKE	SURE	THIS		IS	_-'_"'-_	GROUNDING	LUG
MAKE	SURE	THIS	A	IS	_-'_"'-_
CONNECTED		TO	A		i
KNOWN	GROUND						ADAPTER
							ADAPTER
					H		3-PRONG
					i		3-PRONG
					Li		PLUG

2--PRONG	J
2--PRONG
RECEPTACLE

NOTE: The adapter illustrated is for use onIy if you already

have a properly grounded 2-p:rong receptacle.

The use of any extension cord will cause some loss of

power. To keep this to a minimum and to prevent over- heating and motor burn-out, use the table below to deter- mine the minimum wire size (A,W.G.) extension cord. Use

only 3 wire extension cords which have 3-prong grounding type plugs and 3opole receptacles which accept the too& plug,

Extension	Cord	Length	Wire Size A.W.G.
Up to	100	Ft.	14
100	- 200	Ft.	12
200-	400	Ft.	8

CHECK MOTOR ROTATION

WARNING: FOR YOUR OWN SAFETY, MAKE SURE PLUG IS NOT CONNECTED TO POWER SOURCE OUT* LET WHEN CHANGING MOTOR ROTATION.

The motor must rotate COUNTERCLOCKWISE when viewed from the shaft end to which you wilI mount the pulley, (See page 10}, If it does not, change the direction

according to the instructions furnished with the motor,

motor specifications and emedrkaR requkernents :