Sears 206801, 113.206931 Replacing Cutter Blades, Iiiiii!ii¸i, Blade Wedge Lifterlockscrew Screw

Page 21

maintenance

REPLACING CUTTER BLADES

WARNING: FOR YOUR OWN SAFETY. TURN SWITCH "OFF" AND REMOVE PLUG FROM POWER

SOURCE OUTLET BEFORE ADJUSTING, MAINTAIN- ING, OR LUBRICATING YOUR JOINTER-PLANER.

1.Remove belt guard,

2.Position fence to right . , . approximately I/4 In. beyond cutter blades . . . lock it in place,

3, Lower infeed table all the way down.

4.Place block of wood 6-3/4 in. long between cutter- guard and fence,

5, Hold cutterhead pulley firmly with one hand and loosen tockscrews in each wedge using a 5/32 in. setscrew wrench.

BLADE WEDGE

LIFTERLOCKSCREW

SCREW

6.While holding cutterhead pulley firmly with one hand,

gently pry up each Wedgeusing a screwdriver . re- move wedges and blades.

i _ :_i_iiii:_:i!ii_¸i :

_/i::

BLOCK OF WOOD

	HOLD	PULLEY
	FIRMLY
5/32 IN.	/
SETSCREW	/	TURN COUNTER
	/	TURN COUNTER
WRENCH	/_._	CLOCKWISE
__		TO LOOSEN __

____ •............. ..........

FENCE NOT SHOWN

FOR PICTURE CLARITY

= i

SMALL SCREWDRIVER

Image 21

Contents JOINTER/PLANER with Legs and Motor JOINTER/PLANER onlyMake WOR Kshop KID-PROOF Know Your Power ToolING MaintenanceGetting To Know Your JOINTER-PLANER KickbacksAssembly General SafetyRepair Parts RecommendedConnecting to Power Source Outlet Removing the Plug to or from the OutletOutlet Checking contents Unpacking and checking contents 32 IN. Setscrew CHECKING-CUTTER Blades and ScrewsWrench 114-20TRUSS Side Stiffener Head Screw END Motor Support ATMounting Switch INSTALLINGSliding Guard Mounting Recommended Craftsman Motor and Belt GuardsM, rotate COUNTERC.OCKWiSE whe Check Motor RotationDirection RotationHreJ 3OINTER-PULLEYBELT Guard InstallationOutfeedtable Sliding GUA RDInfeed Slide 8RACKET Cutter Guard 6 ON-OFF Depth of CUT HandwheelSquare tNFEED Fence FaceCutter Guard Parallel condition Infeed Table END HighHead Squaretable Fence Cutter GuardRotate Blade OUT WAY Penc L Wood Your Work BenchOutfeed View Looking UP for Parts Identification Leveling StudsScrewing in the studs will Raise the table Hazardous USE by ChildrenPower Cord Motor CordHold Feeding the Workpiece Planing Wood That is Thicker than 3Jointing Wood That is Wider than 3 Using the Hold DOWN!PUSH Blocks With the GrainAgainst the Grain BEY Eling When planing wood 3/4 in, thick and Narrower thanFollow Same PlaningIiiiii!ii¸i Replacing Cutter BladesBlade Wedge Lifterlockscrew Screw Block of Wood HoldLifter Screw Cutte Setscrew Mark Slots 1, 2 IN, Setscf Wrench32 IN. Setscrew Wrench Lifter Wedge Lockslrew WedgeInfeed Counter ClockwisePlace Guard Tang Spring Center Pivot PINNEW Blade Sharpening Cutter BladesNever Rotate Spring Position aDovetail Spacer and SlideElevating Screw View Looking UP for Parts Identification Recommended Accessories ChartTrouble ShootingHardware for Mounting Tool and Motor Craftsman 6-1/8iNCH JOINTER-PLANER Model No .206801Fence Assembly See for Exploded View See Fgure 5 for Exploded View3425 Key Craftsman 64/8 Inch JOINTER.PLANER Model No .20680121 22 Key Part JOINTER!PLANER with Legs and Motor 113.2068018 Inch JOINTER-PLANER