Sears 113.206931, 206801 manual General Safety, Assembly, Recommended, Repair Parts

addifionaR safety instruchons for mo nter..planer

!3, TO be sure you will make a depth of cut as panned, always lower the infeed tab e S ightty beYOnd the depth Wanted, then raise the table to the desired d_,pth.

•

15; Never leave the Jointer-P aner work area w th the power

On, before the Jointer-Planerhas come to a complete

stop, or without removing and storing the switch key.

WHEN USED WITH A 3450 RPM MOTOR NEVER

SUBSTITUTE OTHER PULLEYS TO NCREASE THIS SPEED BECAUSE IT COULD BE DANGEROUS.

PROM FREQUENT USE OF YOUR JOINTER-PLANER) TO BECOME COMMONPLACE. ALWAYS REMEMBER

THAT A CARELESS FRACTION OF A SECOND IS SUFFICIENT TO INFLICT SEVERE INJURY,

t9. Read and follow the instructions appearing on the

16.Never operate the Jointer-Planer with protective cover

on the unused shaft end of the motor removed.

17, Do not attempt to perform an abnormal or little-used operation without study and the use of adequate hold

down/push blocks, jigs, fixtures, stops, etc.

danger label on the cutter guard.

DANGER - FOR YOUR OWN SAFETY

lB. DO NOT perform tayou_, assembly, or setup work on the tabe while the cutting tool is rotating.

WARNING: THE 2" JOINTER-PLANER PULLEY AND

THE 2-1/2"MOTOR PULLEY FURNISHED WILL RUN

THE CUTTER HEAD AT APPROXIMATELY 4300 RPM

READ AND UNDERSTANDOWNER*S

MANUAL BEFORE OPERATING MACHINE

1 WEAR SAFETY GOGGLES PER ANSI Z87 1 AT ALL TIMES

2 NEVER PERFORM A JOINT1NG OR PLANING OPERATION W_TH CUTTER

HEAD OR DRIVE GLIARD REMOVED

3 NEVER MAKE A JOtNTING OFt PLANING CUT DEEPER THAN _/g INCH

4 ALWAYS USE HOLD DOWN/PUSH SLOCKS EOR JOINTtNG MATERIAL

NARROWER THAN 3 INCHES OR PLANING MATER_AL THINNER THAN 3

INCRES.

WEAR YOUR

The operation of any power tool can result in foreign objects being thrown into the eyes, which can result n

severe eye damage. Always wear safety goggles complying with ANSI Z87.1 (shown on Package) before commencing

power too! operation. Safety Goggles are available at Sears retail or catalog stores.

cortfents

POWER	TOOL		GUARANTEE						2
GENERAL SAFETY				INSTRUCTIONS FOR
POWER	TOOLS								2
ADDITIONAL			SAFETY		INSTRUCTIONS			FOR
JOINTER-PLANER				..........................					3
MOTOR	SPECIFICATIONS					AND	ELECTRICAL
REQUIREMENTS									5
Connecting			to Power			Source	Outlet	........	5
Check	Motor		Rotation			....................			5
UNPACKING		AND		CHECKING CONTENTS ....					6
ASSEMBLY		................................							7
Assembling			Steel	Legs					7
Mounting Jointer-Planer On Recommended
Craftsman		Stand		.........................					8
Checking		Cutterblade				Screws	..............		8
Installing		Sliding		Guard					9
Mounting		Switch		..........................					9
Mounting		Recommended Craftsman						Motor
and Belt		Guards		.......		;
-Check	Mot0r		Rotation			.:_ :..:	.........	;....	10 :
Jointer-PUlley			Beff		G uardlnstaliation			:: :..	i I

GETTING		TO KNOW				YOUR		JOINTER-PLANER	12
Depth		of	Cut	HandwheeJ				..................	12
Fence		Locks		and		Stops		...................	12
Fence		Tilt	Scale			..........................			13
Cutter		Guard		..........................					14
Infeed		Table		..........................					14
On-Off		Switch			...........................				16
BASIC	JOtNTER-PLANER						O PERATION		18
Feeding		the		Workpiece				...................	18
Using		the	Hold		Down/Push			Blocks	19
Beveling			.................................						20
MAINTENANCE				............................					21
Replacing			Cutter			Blades		..................	21
Installing			Cutter		Guard		Spr=ng		23
Sharpening				Cutter		Blades		.................	24
GENERAL		MAINTENANCE						..................	25
LUBRICATION				..............................					25
TROUBLE		SHOOTING							26
RECOMMENDED					ACCESSORIES				26
REPAIR	PARTS			.............................					27