Sears 113 BEY Eling, When planing wood 3/4 in, thick and Narrower than, Follow Same, Planing

Page 20

laner operation

When planing wood 3/4 in, thick and NARROWER than

the hold down/push block, tilt the hold down/push

i block so that it ctears the top of the cutterguard while feed ng.

Never plane wood that is thinner than 1/2 in .... because

it is apt to split or shatter and thus has a greater tenden- cy tO kickbacki

BEY ELING

Adjust	the	fence	to the desired	angle ...tighten		fence
and guard lock knobs,
Follow	the	same	procedure	for jointing	or	planing.

NOTE: Removing only the corner on the edge of a board is known as CHAMFERING.

Normally a chamfer is made with one cut.,, therefore, acut deePer than 1/16 in. may be made.

Use hold down/push blocks for wood under 3 in. wide. PositiOn them so you have control of the workpiece at all times: and so they do not contact the guard or the cutter head,

CHAMFERBEVEL

NOTE: Rabbeting on a Jointer is consid_.red to be a

dangerous operation because it requires removal of the cutter guard and increases the potential of kickback be- cause of excessive depth of cut,

NEVER ATTEMPT TO PERFORM A RABBETING

OPERATION ON THIS JOINTER. DO NOT OPERATE

JOtNTER/PLANER WITH CUTTERHEAD OR BELT

GUARDS REMOVED.

Rabbet cuts should be made on the Radial Saw or Table Saw b_ making two cuts with the sawblade or by using

tbe,Dado Head or Molding Head. Rabbet cuts can alsoRABBET CUT be made using the Shaper or Portable Router.

2O

Image 20

Contents JOINTER/PLANER only JOINTER/PLANER with Legs and MotorKnow Your Power Tool Make WOR Kshop KID-PROOFMaintenance INGGetting To Know Your JOINTER-PLANER KickbacksGeneral Safety AssemblyRepair Parts RecommendedOutlet Connecting to Power Source OutletRemoving the Plug to or from the Outlet Checking contents Unpacking and checking contents CHECKING-CUTTER Blades and Screws 32 IN. SetscrewWrench 114-20TRUSS Side Stiffener Head Screw END Motor Support ATINSTALLING Mounting SwitchSliding Guard Mounting Recommended Craftsman Motor and Belt GuardsCheck Motor Rotation M, rotate COUNTERC.OCKWiSE wheDirection Rotation3OINTER-PULLEYBELT Guard Installation HreJSliding GUA RD OutfeedtableInfeed Slide 8RACKET Cutter Guard 6 ON-OFF Depth of CUT HandwheelCutter Guard Square tNFEEDFence Face Infeed Table END High Parallel conditionHead Squaretable Fence Cutter GuardOutfeed Rotate Blade OUT WAY Penc LWood Your Work Bench Leveling Studs View Looking UP for Parts IdentificationScrewing in the studs will Raise the table Hazardous USE by ChildrenHold Power CordMotor Cord Jointing Wood That is Wider than 3 Feeding the WorkpiecePlaning Wood That is Thicker than 3 Against the Grain Using the Hold DOWN!PUSH BlocksWith the Grain When planing wood 3/4 in, thick and Narrower than BEY ElingFollow Same PlaningReplacing Cutter Blades Iiiiii!ii¸iBlade Wedge Lifterlockscrew Screw Block of Wood HoldCutte Setscrew Mark Slots 1, 2 IN, Setscf Wrench Lifter Screw32 IN. Setscrew Wrench Lifter Wedge Lockslrew WedgeCounter Clockwise InfeedPlace Guard Tang Spring Center Pivot PINSharpening Cutter Blades NEW BladeNever Rotate Spring Position aElevating Screw View Looking UP for Parts Identification DovetailSpacer and Slide Chart Recommended AccessoriesTrouble ShootingCraftsman 6-1/8iNCH JOINTER-PLANER Model No .206801 Hardware for Mounting Tool and Motor3425 Fence Assembly See for Exploded ViewSee Fgure 5 for Exploded View Craftsman 64/8 Inch JOINTER.PLANER Model No .206801 Key21 22 Key Part 8 Inch JOINTER-PLANER JOINTER!PLANER with Legs and Motor113.206801