general safety instructions For power fools
1. KNOW YOUR POWER TOOL
Read and understand the owner's manual and labels
affixed to the tool. Learn its application and
limitations as well as the specific potential hazards peculiar to this tool.
2. GROUND ALL TOOLS
This tool is equipped with an approved
cord and a 3. arong grounding type plug to fit the 3roper grounding tv_ae receptacle. The green conductor
r_ the cord is the grounding w_re. Never connect the green wire to a I,ve terminal.
3. KEEP GUARDS IN PLACE
_r_ working order, and _n proper adjustment and alignment.
protectors (plugs or muffs) dt_Hng extended periods of operation.
13. SECURE WORK
Use clam3s or a vise to hold work when practical. It's safer than using your hand, frees both hands to operate tool.
14. DON'T OVERREACH
Keep proper footing and balance at all times,
15. MAINTAIN TOOLS WITH CARE
<eep toots shart) and clean for Pest and safest
performance. Fo[tow instructions for l[_bricating and chang_ rig accessories.
4. REMOVE ADJUSTING KEYS AND WRENCHES
Form hab, t of checking to see that keys and adjusting wrenches are removed from tool before turning lr on
5. KEEP WORK AREA CLEAN
Cluttered areas and benches inwte accidents. Floor must not be sl operv due to wax o_ sawdust.
-6. AVOID DANGEROUS ENVIRONMENT
Don't use power tools n damp or wet locations or
expose them to rain. Keep work area well ghted,
Provide adequate surrounding work space,
16. DISCONNECT TOOLS
before servicing; when changing accessories such as blades, bits, cutters, etc.
!7. AVOI D ACCI DENTAL STARTING
Make sure switch Is tn "OFF" position before ptuggmg in,
18. USE RECOMMENDED ACCESSORI ES
Consult the owner's manual for recommended
accessories. Foltow the instructiOnS that accompany the accessories. The use of _mproDer accessories may cause hazards.
7.KEEP CHILDREN AWAY
AIr visitors should be kept a safe distance from work
_rea,
8.MAKE WOR KSHOP KID-PROOF
wtth padlocks, master switches or by removing starter keys.
9.DON'T FORCE TOOL
It w_!t do the job better and safer at the rate for which
ttwas designed.
10.USE RIGHT TOOL
Don't force tool or attachment to do a ]ob tt was not designed for.
11, WEAR PROPER APPAREL
Do not wear loose clothing, gloves, neckties or jewelry (rings, wrist watches) to get caught in moving parts.
Nonstip footwear is recommended. Wear protective
hair covering to contain long hair. Roll tong sleeves above the elbow.
12. USE SAFETY GOGGLES (Head Protection)
Wear Safety goggles (must comply with ANS Z87.1 ) at
all times. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. Also, use face or dust mask if cutting operation is dusty, and ear
19. NEVER STAND ON TOOL
Serious injury could occur if the tool is t_pped or if the
cutPng [ool _saccidentally contacted.
Do not _.[ore materials above or near the tool such that _t _s_)ecessary to stand on the too to reach them,
20. CHECK DAMAGED PARTS
Before further use of the tool, a guard or other part that _s damageo should be carefully checked to ensure that _t will operate properly and perform its intended function. Check for alignmem of moving parts, binding of moving
parts, breakage of parts, mounting, and any other
conditions that may ,affect _ts operation. A guard or other part that is damaged should be 3roperly repa_reo or replaced.
21. DIRECTION OF FEED
Feed work into a blade or cutter against the dtrection of rotation of the blade or cutter on y
22.NEVER LEAVE TOOL RUNNING UNATTENDED
Turn power off Don't leave tool untd _t comes to a complete stop.