Bostitch F33PT Maintaining the Pneumatictool, Replacement Parts, Assembly Procedure for Seals

Page 13

MAINTAINING THE PNEUMATICTOOL

When working on air tools, note the warnings in this manual and use extra care evaluating problem tools.

CAUTION: Pusher spring (constant force spring). Caution must be used when working with the spring assembly. The spring is wrapped around, but not attached to, a roller. If the spring is extended beyond its length, the end will come off the roller and the spring will roll up with a snap, with a chance of pinching your hand. Also the edges of the spring are very thin and could cut. Care must also be taken to insure no permanent kinks are put in the spring as this will reduce the springs force.

REPLACEMENT PARTS:

BOSTITCH replacement parts are recommended. Do not use modified parts or parts which will not give equivalent performance to the original equipment.

ASSEMBLY PROCEDURE FOR SEALS:

When repairing a tool, make sure the internal parts are clean and lubricated. Use Parker “O”-LUBE or equivalent on all “O”-rings. Coat each “O”-ring with “O”-LUBE before assembling. Use a small amount of oil on all moving surfaces and pivots. After reassembly add a few drops of BOSTITCH Air Tool Lubricant through the air line fitting before testing.

AIR SUPPLY-PRESSURE AND VOLUME:

Air volume is as important as air pressure. The air volume supplied to the tool may be inadequate because of undersize fittings and hoses, or from the effects of dirt and water in the system. Restricted air flow will prevent the tool from receiving an adequate volume of air, even though the pressure reading is high. The results will be slow operation, misfeeds or reduced driving power. Before evaluating tool problems for these symptoms, trace the air supply from the tool to the supply source for restrictive connectors, swivel fittings, low points containing water and anything else that would prevent full volume flow of air to the tool.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents F33PT / F33PTSM Introduction Limited Warranty U.S. and Canada OnlyIndex AIR Supplyand Connections Safety InstructionsLoadingtool OperationFastener Specifications Seriestool SpecificationsTool AIR Fitting Operating PressureLubrication OperationTo Prevent Accidental Injuries Loadingthe F Series ToolsTo Adjust the Fastener Depth Control Fastener Depth Control AdjustmentDirectional Exhaust Deflector Removing NailsPage Before Handling or Operating this Tool Tool OperationSequential Trip Operation Graytrigger Contact Trip Operation Black TriggerTool Operation Important Read Carefully Sequential TripSequential Trip Operation Tool Operation CheckContacttrip Operation Assembly Procedure for Seals Replacement PartsAIR SUPPLY-PRESSURE and Volume Maintaining the PneumatictoolProblem Cause Correction Trouble ShootingÍndice IntroducciónNota Garantía Limitada Sólo EE.UU. y CanadáSuministro DE Airey Conexiones Instrucciones DE SeguridadAL Cargar LA Herramienta OperaciónEspecificaciones DE LA Herramienta Serie F Mantenimiento DE LA HerramientaFuncionamiento Lubricación Funcionamiento continuaciónPara Prevenir Lesiones Accidentales Carga DE LAS Herramientas Serie FDeflector DE Escape Direccional Ajuste DEL Control DE Profundidaddel ClavoExtracción DE Clavos Para Ajustar EL Control DE Profundidad DEL ClavoFigura Antes DE Manipular U Operar Esta Herramienta Funcionamiento DE LA HerramientaFuncionamiento DEL Disparo Secuencial Gatillo Gris Funcionamiento DEL Disparo DE Contacto Gatillo NegroFuncionamiento DE LA Herramienta Continuación ¡IMPORTANTE LEA Detenidamente Disparo SecuencialFuncionamiento DEL Disparo Secuencial Revisión Funcional DE LA HerramientaFuncionamiento DEL Disparo DE Contacto Mantenimiento DE LA Herramienta Neumática Presión Y Volumen DEL Suministro DE AirePiezas DE Repuesto Procedimiento DE Ensamblaje Para LOS SellosRevise el equipo de suministro de aire Solución DE ProblemasGarantie Limitée É.-U. et Canada seulement RemarqueAlimentation EN AIR Comprimé ET Raccordement Consignes DE SécuritéChargement DE L’APPAREIL FonctionnementSpécifications DES Attaches Entretien DE L’APPAREILGarniture Pneumatiquede L’OUTIL Pression DE FonctionnementAlimentation EN AIR ET Connexions Utilisation suiteLubrification Pour Prévenir Tout Accident Chargement DES Outils DE LA Série FDéflecteur DE L’ÉCHAPPEMENT Directionnel Commandede Réglage DE Profondeurde FixationRetrait DES Clous Pour Régler LA Profondeur DE FixationPage Utilisation Fonctionnement DE L’OUTILDéclenchement Séquentiel Gâchette Grise Utilisation DU Déclencheur PAR Contact Gâchette NoireUtilisation DE L’OUTIL Suite Important À Lire Attentivement Déclencheur SéquentielUtilisation DU Déclencheur Séquentiel Vérification DE L’ÉTATDE Marche DE L’OUTILFonctionnement DE LA Butée DE Déclenchement Pression ET Volume DE L’ALIMENTATION D’AIR Maintenance DE L’OUTILPNEUMATIQUEPièces DE Rechange Procédure DE Montage DES JointsAttaches coincées dans l’outil Dépannage
Related manuals
Manual 3 pages 22.58 Kb

F21PL, F33PT, F33PTSM, F21PL2, F28WW specifications

Bostitch is renowned for its high-quality nailers and fasteners, and its range of products including the F28WW, F21PL2, F33PTSM, F33PT, and F21PL showcases innovations in construction and woodworking. Each of these models is designed to cater to specific needs, making them essential tools for professionals and DIY enthusiasts alike.

The Bostitch F28WW is a lightweight framing nailer that is particularly well-suited for wall framing and sheathing applications. It features a unique flush nose design that allows users to navigate tight spaces with ease. Its adjustable depth control ensures precise nail placement, while the tool-free jam clearance saves valuable time in the event of a jam.

Next is the F21PL2, which combines the functions of both a framing nailer and a brad nailer. This versatility is ideal for those handling diverse projects, from framing walls to finishing touches. The F21PL2 is equipped with a Pushbutton Depth Adjustment feature, which allows users to quickly set the nail depth according to materials, ensuring high-quality finishes.

The Bostitch F33PTSM is designed for trim work, offering a precision that makes it a go-to tool for trim carpenters. Its SmartPoint technology provides accurate nail placement and eliminates the need for the user to press the nailer against the workpiece before firing. This feature, coupled with its tool-free depth adjustment, allows for flexibility and precision.

Similarly, the F33PT is well-regarded for its lightweight design and superior maneuverability. It utilizes a Tool-Free Depth Adjustment feature that enables users to quickly adapt the nail depth for better results on different materials. Its durable construction ensures longevity and reliability on the job site.

Rounding out the lineup is the F21PL, which focuses primarily on framing and metal connector applications. This nailer is known for its high-efficiency performance, featuring a patented anti-dry fire mechanism that prevents accidental firing when nails are not loaded. The F21PL is also compatible with a wide range of fasteners, enhancing its adaptability for various tasks.

Together, these Bostitch models exemplify the brand's commitment to quality, efficiency, and user-friendly technologies, making them indispensable for construction professionals and hobbyists looking to achieve high standards in their woodworking projects. Their blend of performance-enhancing features and thoughtful designs truly sets Bostitch nailers apart in the market.
Top Page Image Contents