Bostitch 600 Tool Operation Check, Trigger Operated Tool, Tool Must not Cycle, Tool Must Cycle

Page 8

TOOL OPERATION CHECK:

CAUTION: Remove all fasteners from tool before performing tool operation check.

1.TRIGGER OPERATED TOOL:

A.With finger off the trigger, hold the tool with a firm grip on the handle.

B.Place the nose of the tool against the work surface.

C.Pull the trigger to drive. Release the trigger and cycle is complete.

CAUTION: THE TOOL WILL CYCLE EACH TIME THE TRIGGER IS PULLED!

2.CONTACT TRIP OPERATION:

A.With finger off the trigger, press the contact trip against the work surface.

THE TOOL MUST NOT CYCLE.

B.Hold the tool off the work surface, and pull the trigger.

THE TOOL MUST NOT CYCLE.

C.With the tool off the work surface, pull the trigger. Press the contact trip against the work surface.

THE TOOL MUST CYCLE.

D.Without touching the trigger, press the contact trip against the work surface, then pull the trigger.

THE TOOL MUST CYCLE.

3.SEQUENTIAL TRIP OPERATION:

A.Press the contact trip against the work surface, without touching the trigger.

THE TOOL MUST NOT CYCLE.

B.Hold the tool off the work surface and pull the trigger.

THE TOOL MUST NOT CYCLE.

Release the trigger. The trigger must return to the trigger stop on the frame.

C.Pull the trigger and press the contact trip against the work surface.

THE TOOL MUST NOT CYCLE.

D.With finger off the trigger, press the contact trip against the work surface. Pull the trigger.

THE TOOL MUST CYCLE.

IN ADDITION TO THE OTHER WARNINGS CONTAINED IN THIS MANUAL OBSERVE THE FOLLOWING FOR SAFE OPERATION

•Use the BOSTITCH pneumatic tool only for the purpose for which it was designed.

•Never use this tool in a manner that could cause a fastener to be directed toward the user or others in the work area.

•Do not use the tool as a hammer.

•Always carry the tool by the handle. Never carry the tool by the air hose.

•Do not alter or modify this tool from the original design or function without approval from

BOSTITCH, INC.

•Always be aware that misuse and improper handling of this tool can cause injury to yourself and others.

•Never clamp or tape the trigger or contact trip in an actuated position.

•Never leave a tool unattended with the air hose attached.

•Do not operate this tool if it does not contain a legible WARNING LABEL.

•Do not continue to use a tool that leaks air or does not function properly. Notify your nearest BOSTITCH representative if your tool continues to experience functional problems.

-8-

Page 7 Page 9
Image 8
Page 7 Page 9
Contents 600, 700 & 800 Series Index Limited Warranty U.S. and Canada OnlyIntroduction Safety Instructions AIR Supply and ConnectionsLoading Tool Operation600, 700 & 800 Series Tool Specifications Lubrication DIAL-A-DEPTH Fastener Control Adjustment To Adjust DIAL-A Depth Fastener Control AdjustmentLoading the 600,700 To Prevent Accidental InjuriesTool Operation Before Handling or Operating this ToolTrigger Operation Contact Trip OperationTool Operation Check Trigger Operated ToolTool Must not Cycle Tool Must CycleReplacement Parts Assembly Procedure for SealsAIR SUPPLY-PRESSURE and Volume Maintaining the Pneumatic ToolTrouble Shooting Problem Cause CorrectionAccessories Available Directional Exhaust DeflectorQuick Release Magazine Recommended ToolsIntroducción ÍndiceNota Garantía Limitada Sólo EE.UU. y CanadáInstrucciones DE Seguridad Suministro DE Aire Y ConexionesAL Cargar LA Herramienta OperaciónEspecificaciones DE LAS Herramientas Series 600, 700 Y Lubricación Cómo Cargar EL 600, 700 Y Ajuste DE Control Para Engrapar DIAL-A-DEPTHPara Ajustar EL Control DE Engrapado DIAL-A-DEPTH Advertencia Para Impedir Lesiones AccidentalesOperación DE LA Herramienta Antes DE Manejar U Operar Esta HerramientaOperación DE Disp ARO POR Contacto Operación DE Disp ARO SecuencialVerificación DE LA Operación DE LA Herramienta Herramienta Operada POR GatilloOperación POR Disp ARO Secuencial LA Herramienta no Debe Efectuar SU CicloPresión Y Volumen DEL Suministro DE Aire Mantenimiento DE LA Herramienta NeumáticaPartes DE Reemplazo Procedimiento DE Ensamble Para LOS SellosCausa Corrección ProblemaDiagnóstico DE Falla Deflector DE Escape Direccional Depósito DE Liberación RápidaAccesorios Disponibles Herramientas RecomendadasGarantie Limitée É.-U. et Canada seulement SommaireRemarque Consignes DE Sécurité Alimentation EN AIR Comprimé ET RaccordementChargement DE L’APPAREIL FonctionnementDonnées Techniques DES Outils DES Séries 600, 700 ET OpérationLubrification Pour Prévenir UN Accident Commande DE Réglage DES Attaches DIAL-A-DEPTHChargement EL 600, 700 ET Avant DE Manipuler OU D’UTILISER CET Outil Mode D’EMPLOIFonctionnement DE L’APPAREIL Vérification DU Système DE Déclenchement Déclenchement P AR LA DétenteSystème DE Sécurité À LA Volée Système DE Sécurité AU COUP-PAR-COUPProcédure D’ASSEMBLAGE DES Garnitures Alimentation D’AIR Pression VolumePièces DE Rechange Problèmes DE Fonctionnement Problème Cause CorrectionAccessoires Disponibles Outils RecommandésDéflecteur D’ÉCHAPPEMENT Directionnel Magasin À Dégagement Rapide

600, 650S4-1 specifications

The Bostitch 650S4-1,600 is an advanced pneumatic stapler designed for a wide range of fastening tasks in both professional and DIY settings. Built for durability and efficiency, this tool delivers high performance while maintaining user comfort, making it a preferred choice among contractors and woodworkers alike.

One of the standout features of the Bostitch 650S4-1,600 is its robust construction, designed to withstand the rigors of daily use. The stapler operates on a pneumatic system, requiring an air compressor to provide power, which allows it to deliver consistent performance without the need for batteries or electricity. This feature makes it not only reliable but also ideal for outdoor jobs where power sources are limited.

The stapler has a magazine capacity that holds up to 160 staples, minimizing the need for frequent reloads and allowing users to work more efficiently. It is compatible with a variety of Bostitch staples, specifically 18-gauge and ¾-inch crown staples, which are perfect for applications like upholstery, insulation, woodworking, and general construction. This versatility further enhances its appeal, making it suitable for various projects.

Another significant characteristic of the Bostitch 650S4-1,600 is its adjustable depth control, which allows users to set the stapler to drive staples to the desired depth into different materials. This feature helps in achieving clean and precise fastening, especially when working with materials of varying thicknesses. The staple exit is designed to minimize jamming, making operation smoother and reducing downtime during tasks.

In terms of safety, the Bostitch 650S4-1,600 incorporates a trigger safety mechanism that prevents accidental firing. This added layer of protection is crucial, especially in busy work environments where multiple users may be present. The integrated rubber grip provides comfort and control, reducing hand fatigue during prolonged use.

Additionally, the unit is also lightweight, which enhances maneuverability and ease of use, especially when tackling overhead projects or tight spaces. With its combination of power, precision, and flexibility, the Bostitch 650S4-1,600 stands out in the realm of pneumatic staplers, making it an excellent investment for anyone in need of a reliable fastening solution.
Top Page Image Contents