Bostitch 650S4-1 Maintaining the Pneumatic Tool, Replacement Parts, Assembly Procedure for Seals

Page 9

MAINTAINING THE PNEUMATIC TOOL

When working on air tools, note the warnings in this manual and use extra care evaluating problem tools.

CAUTION: Pusher spring (constant force spring). Caution must be used when working with the spring assembly. The spring is wrapped around, but not attached to, a roller. If the spring is extended beyond its length, the end will come off the roller and the spring will roll up with a snap, with a chance of pinching your hand. Also the edges of the spring are very thin and could cut. Care must also be taken to insure no permanent kinks are put in the spring as this will reduce the springs force.

REPLACEMENT PARTS:

BOSTITCH replacement parts are recommended. Do not use modified parts or parts which will not give equivalent performance to the original equipment.

ASSEMBLY PROCEDURE FOR SEALS:

When repairing a tool, make sure the internal parts are clean and lubricated. Use Parker “O”-LUBE or equivalent on all “O”-rings. Coat each “O”-ring with “O”-LUBE before assembling. Use a small amount of oil on all moving surfaces and pivots. After reassembly add a few drops of BOSTITCH Air Tool Lubricant through the air line fitting before testing.

AIR SUPPLY-PRESSURE AND VOLUME:

Air volume is as important as air pressure. The air volume supplied to the tool may be inadequate because of undersize fittings and hoses, or from the effects of dirt and water in the system. Restricted air flow will prevent the tool from receiving an adequate volume of air, even though the pressure reading is high. The results will be slow operation, misfeeds or reduced driving power. Before evaluating tool problems for these symptoms, trace the air supply from the tool to the supply source for restrictive connectors, swivel fittings, low points containing water and anything else that would prevent full volume flow of air to the tool.

-9-

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 600, 700 & 800 Series Limited Warranty U.S. and Canada Only IntroductionIndex AIR Supply and Connections Safety InstructionsLoading Tool Operation600, 700 & 800 Series Tool Specifications Lubrication To Adjust DIAL-A Depth Fastener Control Adjustment DIAL-A-DEPTH Fastener Control AdjustmentLoading the 600,700 To Prevent Accidental InjuriesBefore Handling or Operating this Tool Tool OperationTrigger Operation Contact Trip OperationTrigger Operated Tool Tool Operation CheckTool Must not Cycle Tool Must CycleAssembly Procedure for Seals Replacement PartsAIR SUPPLY-PRESSURE and Volume Maintaining the Pneumatic ToolProblem Cause Correction Trouble ShootingDirectional Exhaust Deflector Accessories AvailableQuick Release Magazine Recommended ToolsÍndice IntroducciónNota Garantía Limitada Sólo EE.UU. y CanadáSuministro DE Aire Y Conexiones Instrucciones DE SeguridadAL Cargar LA Herramienta OperaciónEspecificaciones DE LAS Herramientas Series 600, 700 Y Lubricación Ajuste DE Control Para Engrapar DIAL-A-DEPTH Cómo Cargar EL 600, 700 YPara Ajustar EL Control DE Engrapado DIAL-A-DEPTH Advertencia Para Impedir Lesiones AccidentalesAntes DE Manejar U Operar Esta Herramienta Operación DE LA HerramientaOperación DE Disp ARO POR Contacto Operación DE Disp ARO SecuencialHerramienta Operada POR Gatillo Verificación DE LA Operación DE LA HerramientaOperación POR Disp ARO Secuencial LA Herramienta no Debe Efectuar SU CicloMantenimiento DE LA Herramienta Neumática Presión Y Volumen DEL Suministro DE AirePartes DE Reemplazo Procedimiento DE Ensamble Para LOS SellosProblema Diagnóstico DE FallaCausa Corrección Depósito DE Liberación Rápida Deflector DE Escape DireccionalAccesorios Disponibles Herramientas RecomendadasSommaire RemarqueGarantie Limitée É.-U. et Canada seulement Alimentation EN AIR Comprimé ET Raccordement Consignes DE SécuritéChargement DE L’APPAREIL FonctionnementOpération Données Techniques DES Outils DES Séries 600, 700 ETLubrification Commande DE Réglage DES Attaches DIAL-A-DEPTH Chargement EL 600, 700 ETPour Prévenir UN Accident Mode D’EMPLOI Fonctionnement DE L’APPAREILAvant DE Manipuler OU D’UTILISER CET Outil Déclenchement P AR LA Détente Vérification DU Système DE DéclenchementSystème DE Sécurité À LA Volée Système DE Sécurité AU COUP-PAR-COUPAlimentation D’AIR Pression Volume Pièces DE RechangeProcédure D’ASSEMBLAGE DES Garnitures Problème Cause Correction Problèmes DE FonctionnementOutils Recommandés Accessoires DisponiblesDéflecteur D’ÉCHAPPEMENT Directionnel Magasin À Dégagement Rapide

600, 650S4-1 specifications

The Bostitch 650S4-1,600 is an advanced pneumatic stapler designed for a wide range of fastening tasks in both professional and DIY settings. Built for durability and efficiency, this tool delivers high performance while maintaining user comfort, making it a preferred choice among contractors and woodworkers alike.

One of the standout features of the Bostitch 650S4-1,600 is its robust construction, designed to withstand the rigors of daily use. The stapler operates on a pneumatic system, requiring an air compressor to provide power, which allows it to deliver consistent performance without the need for batteries or electricity. This feature makes it not only reliable but also ideal for outdoor jobs where power sources are limited.

The stapler has a magazine capacity that holds up to 160 staples, minimizing the need for frequent reloads and allowing users to work more efficiently. It is compatible with a variety of Bostitch staples, specifically 18-gauge and ¾-inch crown staples, which are perfect for applications like upholstery, insulation, woodworking, and general construction. This versatility further enhances its appeal, making it suitable for various projects.

Another significant characteristic of the Bostitch 650S4-1,600 is its adjustable depth control, which allows users to set the stapler to drive staples to the desired depth into different materials. This feature helps in achieving clean and precise fastening, especially when working with materials of varying thicknesses. The staple exit is designed to minimize jamming, making operation smoother and reducing downtime during tasks.

In terms of safety, the Bostitch 650S4-1,600 incorporates a trigger safety mechanism that prevents accidental firing. This added layer of protection is crucial, especially in busy work environments where multiple users may be present. The integrated rubber grip provides comfort and control, reducing hand fatigue during prolonged use.

Additionally, the unit is also lightweight, which enhances maneuverability and ease of use, especially when tackling overhead projects or tight spaces. With its combination of power, precision, and flexibility, the Bostitch 650S4-1,600 stands out in the realm of pneumatic staplers, making it an excellent investment for anyone in need of a reliable fastening solution.
Top Page Image Contents