Harbor Freight Tools 96067 operating instructions To Align the SAW Table to the SAW Blade

Page 34

TO ALIGN THE SAW TABLE TO THE SAW BLADE

1.Set up the machine with the Table in place and the Saw Blade/Arbor installed.

2.Set the Table Trunnion to zero.

3.Place the Miter Gauge in the Table Slot closest to the Saw Blade.

4.Hold a pencil against the face of the Miter Gauge while touching the face of the Saw Blade. As you rotate the Saw Blade, the high spot on the Blade will push the pencil away. Mark the high spot with chalk or a felt marker.

5.Reposition the pencil, the Miter Gauge, and the high spot on the Saw Blade together at the infeed end of the Table.

6.Rotate the Saw Blade, and bring the Miter Gauge and the high spot together at the infeed end of the Table. Make sure to keep the pencil in the same spot against the Miter Gauge.

7.The Table is aligned if the pencil tip touches the Saw Blade with the same touch and in the same place all the way around the Blade. The Table is not aligned if the Saw Blade pushes the pencil or there is a gap between the pencil tip and Blade. If the Table is not aligned, loosen all four Capscrews attaching the Table to the Trunnions. Adjust the Table. Then repeat Steps #2, #3, #4, #5, #6. Once alignment is achieved, tighten all four Capscrews.

TO ALIGN THE SAW TABLE 90 DEGREES TO THE SAW BLADE

1.Hold a T-Square on the Table and against the Saw Blade with the high spot 90 degrees from the T-Square. Make sure the T-Square does not touch the Saw Blade teeth.

2.If the Table is not 90 degrees to the Saw Blade loosen the front and back Trunnion Handles.

3.Move the Table enough so the T-Square’s two edges are flush with both the Table and Saw Blade.

4.Use Phillips screwdriver to reset the Trunnion’s 0 Degree Indicator to zero.

5.Loosen the Trunnion Locks and slightly move the Table. If the Table does not automatically stop at 0 degrees use a small screwdriver to adjust the Setscrew stop. The Table should stop at 0 degrees each time.

SKU 96067

For technical questions, please call 1-800-444-3353.

Page 34

Image 34

Contents Woodworking Machine Contents GroundingParts Lists and Diagrams Specifications Save This Manual General Safety RulesPersonal Safety Work AreaService Tool Use And CareSpecific Safety Rules Mechanical PrecautionsNoise Precaution Table SAW Safety RulesNever attempt to cut more than one workpiece at a time SKU For technical questions, please call Drill Press Safety Rules Never attempt to drill more than one workpiece at a timeLathe Safety Rules ROUTER/SHAPER Safety Rules Always feed the workpiece against the rotation of the CutterHorizontal Boring Safety Rules Disc Sander Safety RulesMISC. Safety Rules Extension Cords See Figure B, nextUnpacking SymbologyFeet Product Features FiguredTo Adjust Speed Belts and Pulleys Power KEYTo Move the Powerhead To Move the Quill FeedTo Mount Collets with the Drawbar To Move the CarriageSee Figure E and Assy. Diagram, Assembly Instructions To Attach the Shelf to the StandTo Install the Casters See Figure F, next page and Assy. Diagram,To Mount the Machine Onto the Stand See Figure I, next page and Assy. Diagram, To Attach a SAW Blade to the ArborTo Install the Lower Blade Guard See Figure J and Assy. Diagram,See Figure K and Assy. Diagram, To Assemble the Main TableTo Install the Extension Table See Figure L and Assy. Diagram,See Figure M and Assy. Diagram, To Install the RIP Fence and TOP GuardTo Install the Miter Gauge Assy. Diagram,To SET UP the Vertical Drill Press To Install the Disc SanderSee Figure P, next To SET UP the Horizontal Boring Tool Figure PTo SET UP the Router To SET UP the ShaperSee Installing and Using the Cutter Guard To SET UP the LatheFigure S See Figure T Figure TTo Align the SAW Table to the SAW Blade To Align the SAW Degrees to the SAW BladeTo Align the Miter Gauge To Adjust the SAW TABLE’S 45 Degree StopTo Align the Extension Degrees to the SAW Blade To Align the SAW Degrees to the Powerhead To SET the Carriage Bumper BoltTo Align the Lathe Tailstock with the Powerhead Speed Chart Parts List Cabinet & CastersAssembly Diagram Cabinet & Casters Parts List Main BED Assembly Diagram Main BED Parts List -Head Assy Parts List head assy. Assembly Diagram Head Assy Parts List Carriage Assy Assembly Diagram Carriage Assy Parts List SAW Table Assy Assembly Diagram SAW Table Assy Parts List SAW Guard Assy Assembly Diagram SAW Guard Assy Parts List RIP Fence Assembly Diagram Parts List & ASSY. Diagram Lathe Tailstock Assy Parts List & ASSY. Diagram EXT. Table Assy Parts List & ASSY. Diagram Sanding Disc Assy Parts List & ASSY. Diagram Tool Mounting Assemblies Parts List & ASSY. Diagram Tool Rest Parts List & ASSY. Diagram Miter Gauge Assy Parts List Electrical System Assembly Diagram Electrical System Limited 1 year / 90 Day warranty Please Read the Following Carefully