Harbor Freight Tools 96067 operating instructions To Align the Lathe Tailstock with the Powerhead

Page 37

5.If the Table is not perfectly squared with the Drill Bit, adjust the Table Stops with a wrench.

6.Recheck the Table’s 90 degree setting, and correct as needed.

TO ALIGN THE LATHE TAILSTOCK WITH THE POWERHEAD

1.Install the Drill Chuck/Drill Bit in the Horizontal Boring Tool. Make sure the Drill Bit is straight and long.

2.Remove the saw Table and Extension Table from the machine. Then mount the Tailstock with the Tail Center installed.

3.With the Drill Bit tip and Tail Center almost touching, check their alignment.

4.To vertically align the Drill Bit and Tail Center, raise or lower the Tailstock. Once aligned, loosen, position, and tighten the Collar.

5.To horizontally align, use an allen wrench to loosen the Socket Head Capscrew. Move sideways for alignment. Then retighten.

SKU 96067

For technical questions, please call 1-800-444-3353.

Page 37

Image 37
Contents Woodworking Machine Grounding ContentsParts Lists and Diagrams Specifications Personal Safety General Safety RulesSave This Manual Work AreaTool Use And Care ServiceMechanical Precautions Specific Safety RulesTable SAW Safety Rules Noise PrecautionNever attempt to cut more than one workpiece at a time SKU For technical questions, please call Never attempt to drill more than one workpiece at a time Drill Press Safety RulesLathe Safety Rules Always feed the workpiece against the rotation of the Cutter ROUTER/SHAPER Safety RulesDisc Sander Safety Rules Horizontal Boring Safety RulesMISC. Safety Rules See Figure B, next Extension CordsUnpacking SymbologyFeet Figured Product FeaturesTo Move the Powerhead Power KEYTo Adjust Speed Belts and Pulleys To Move the Quill FeedTo Move the Carriage To Mount Collets with the DrawbarTo Install the Casters Assembly Instructions To Attach the Shelf to the StandSee Figure E and Assy. Diagram, See Figure F, next page and Assy. Diagram,To Mount the Machine Onto the Stand To Attach a SAW Blade to the Arbor See Figure I, next page and Assy. Diagram,See Figure J and Assy. Diagram, To Install the Lower Blade GuardTo Assemble the Main Table See Figure K and Assy. Diagram,See Figure L and Assy. Diagram, To Install the Extension TableTo Install the Miter Gauge To Install the RIP Fence and TOP GuardSee Figure M and Assy. Diagram, Assy. Diagram,To SET UP the Vertical Drill Press To Install the Disc SanderSee Figure P, next Figure P To SET UP the Horizontal Boring ToolTo SET UP the Router To SET UP the ShaperSee To SET UP the Lathe Installing and Using the Cutter GuardFigure S Figure T See Figure TTo Align the SAW Degrees to the SAW Blade To Align the SAW Table to the SAW BladeTo Align the Miter Gauge To Adjust the SAW TABLE’S 45 Degree StopTo Align the Extension Degrees to the SAW Blade To SET the Carriage Bumper Bolt To Align the SAW Degrees to the PowerheadTo Align the Lathe Tailstock with the Powerhead Parts List Cabinet & Casters Speed ChartAssembly Diagram Cabinet & Casters Parts List Main BED Assembly Diagram Main BED Parts List -Head Assy Parts List head assy. Assembly Diagram Head Assy Parts List Carriage Assy Assembly Diagram Carriage Assy Parts List SAW Table Assy Assembly Diagram SAW Table Assy Parts List SAW Guard Assy Assembly Diagram SAW Guard Assy Parts List RIP Fence Assembly Diagram Parts List & ASSY. Diagram Lathe Tailstock Assy Parts List & ASSY. Diagram EXT. Table Assy Parts List & ASSY. Diagram Sanding Disc Assy Parts List & ASSY. Diagram Tool Mounting Assemblies Parts List & ASSY. Diagram Tool Rest Parts List & ASSY. Diagram Miter Gauge Assy Parts List Electrical System Assembly Diagram Electrical System Please Read the Following Carefully Limited 1 year / 90 Day warranty