RIDGID JP06101 manual 235$725·60$18$

Page 1

-3

23(5$725·60$18$/

PP-2,17(5

3/$1(5

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.

SAVE THIS MANUAL FOR

FUTURE REFERENCE

Part No. SP6442

Image 1

Contents 235$725·60$18$ Safety Instructions For Jointer/Planer Table of ContentsMajor Hazards Before Using the Jointer/PlanerSafety Labels and Indicators on the Jointer/Planer Inspect Your Workpiece Plan Ahead To Protect Your Eyes, Hands, Face and EarsBefore Leaving the Jointer/Planer Whenever Jointer/Planer Is RunningKeep Children Away Don’t Force ToolPower Supply and Motor Specifications Motor Specifications and Electrical RequirementsGlossary of Terms for Woodworking Volt, 60 Hz. Tool Information General Electrical ConnectionsChanging Motor Voltage Prong Plug Properly Grounded Outlet GroundingWire Sizes Motor Safety ProtectionExtension Gauge A.W.G Cord Length Unpacking and Checking Contents Loose Parts Hex Nut Loose Parts From Hardware PackHex Nut 16-18 Cabinet and Motor Mount Assembly AssemblyMotor Assembly with Switch Install the Leveling FeetMounting the Motor Mounting Jointer Table to Cabinet Tensioning Belt and Installing Rear PanelBelt Align Belt Tighten Motor Mount NutsInstalling Handwheel Installing the Pulley GuardSerr 3/16-24 x 3/8 Belt Guard 20 x 5/8Attach Sawdust Chute Adjusting Table ExtensionTool Storage Sawdust Chute Screw Wing 1/4-20 x 1/2 Outfeed Socket Head Screw Extension even with Outfeed tableAssembly Fence Nut Mount Install Cutter Head GuardAssemble Fence To Bed Fence Lock Knob Nut Washer 1/2 Actual Size NotAdjusting the Leveling Feet Adjusting Guard SpringCutter Head Guard Functional Check Pan Head Screw KnobFence Sliding Knob Getting to Know Your Jointer/PlanerDepth of Cut Handwheel Nameplate Model/Serial Fence Tilt Bevel KnobOn-Off Switch Alignments Cutter Knife Alignment/Adjustments11/16 Wide New Blade Second Cutting Ground Surface Edge Cutter Knife SharpeningChecking Outfeed Table Alignment Outfeed Table AdjustmentOutfeed Table Too High Result Outfeed Table Too Low ResultFence Tilt Use and Bevel Stop Adjustment Adjusting Table GibsAngle Gauge Use Stop Screw BarBefore Each Use Safety Instructions for Basic Jointer/Planer OperationFence Slide Lock Knob Bevel Lock Handle Feeding the Workpiece All Operations Always Use Push Blocks When Planing, Beveling Or ChamferingPush blocks and push sticks Plan your workBefore Leaving the jointer/planer Inspect your workpieceDepth of Cut Handwheel Operation Basic Jointer/Planer Cutting OperationsStop Pin Operation Feeding the WorkpieceJointing PlaningBeveling/Chamfering Jointing Without Push BlocksRabbeting Using the Hold-Down/Push-BlocksSupport Long Workpieces Face Rabbet End EdgeSliding Lock Knob Sliding Fence OperationWiring Diagram Maintenance and LubricationMaintenance LubricationGeneral Troubleshooting GuideTrouble Probable Cause Remedy Motor Parts List for Ridgid 6-1/8 Jointer/Planer Model No. JP06101 Repair PartsKey Description Always order by Part Number Not by Key Number DescriptionRepair Parts Repair Parts Repair Parts Repair Parts Repair Parts JEG6 Call DAY Satisfaction Guarantee Policy

23(5$725·6￿0$18$/

23(5$725·60$18$/