RIDGID JP06101 manual Whenever Jointer/Planer Is Running, Before Leaving the Jointer/Planer

Page 6

Safety Instructions For Jointer/Planer (continued)

When jointing or rabbeting:

-Never joint or bevel workpieces less than 3/4 inch wide or 1/4 inch thick.

-Always use the hold-down/push-blocks when jointing or beveling wood whenever possible.

-When rabbeting, always make cuts in 1/8" incre- ments or less.

When planing or beveling:

-Never plane wood thinner than 1/2 inch.

-Always use hold-down/push-blocks when planing wood.

-Never cut Freehand. Guide your workpiece solidly against the fence and table top.

-Make sure there’s no debris between the workpiece and its supports.

Use extra caution with large, very small or awkward workpieces.

Use extra supports (tables, saw horses, blocks, etc.) for any workpiece large enough to tip when not held down to the table top. Never use another person as additional support or to help feed, support or pull the workpiece.

Never cut more than one workpiece at a time.

Never turn your jointer/planer “ON” before clearing everything except the workpiece and related support devices off the table.

Before trying a new or little used operation, carefully plan your hand placement. Make sure you have proper hold-down/push-blocks, jigs, fixtures, stops, etc. ready to use.

Whenever Jointer/Planer Is Running

WARNING: Don't allow familiarity (gained from fre- quent use of your jointer/planer) cause a careless mis- take. Always remember that a careless fraction of a second is enough to cause a severe injury.

Before actually cutting with the jointer/planer, let it run for a while. If it makes an unfamiliar noise or vibrates a lot, stop immediately. Turn the jointer/planer off. Unplug the jointer/planer. Do not restart until finding and correcting the problem.

Keep Children Away.

Keep all visitors a safe distance from the jointer/planer.

Make sure bystanders are clear of the jointer/planer and workpiece.

Don’t Force Tool.

Let the cutter head reach full speed before cutting.

Feed the workpiece into the jointer/planer only fast enough to let the tool cut without bogging down or binding.

Before freeing jammed material.

Turn switch “OFF”.

Wait for all moving parts to stop.

Unplug the jointer/planer.

Check knives for sharpness and nicks before starting again.

Before Leaving the Jointer/Planer

Turn the jointer/planer off.

Wait for knives to come to a complete stop.

Unplug the jointer/planer.

Make workshop child-proof. Lock the shop. Disconnect master switches. Remove the yellow switch key. Store it away from children and others not qualified to use the tool.

WARNING:

The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always wear eye protection which is marked to comply wtih ANSI Z87.1.

Look for this symbol to point out important safety precautions. It means attention!!! Your safety is in- volved.

SAVE THESE INSTRUCTIONS

6

Image 6
Contents 235$725·60$18$ Table of Contents Safety Instructions For Jointer/PlanerBefore Using the Jointer/Planer Major HazardsSafety Labels and Indicators on the Jointer/Planer Plan Ahead To Protect Your Eyes, Hands, Face and Ears Inspect Your WorkpieceKeep Children Away Whenever Jointer/Planer Is RunningBefore Leaving the Jointer/Planer Don’t Force ToolMotor Specifications and Electrical Requirements Power Supply and Motor SpecificationsGlossary of Terms for Woodworking Changing Motor Voltage General Electrical ConnectionsVolt, 60 Hz. Tool Information Prong Plug Properly Grounded Outlet GroundingMotor Safety Protection Wire SizesExtension Gauge A.W.G Cord Length Unpacking and Checking Contents Loose Parts Loose Parts From Hardware Pack Hex NutHex Nut 16-18 Assembly Cabinet and Motor Mount AssemblyInstall the Leveling Feet Motor Assembly with SwitchMounting the Motor Belt Tensioning Belt and Installing Rear PanelMounting Jointer Table to Cabinet Align Belt Tighten Motor Mount NutsSerr 3/16-24 x 3/8 Belt Guard Installing the Pulley GuardInstalling Handwheel 20 x 5/8Tool Storage Sawdust Chute Screw Wing 1/4-20 x 1/2 Adjusting Table ExtensionAttach Sawdust Chute Outfeed Socket Head Screw Extension even with Outfeed tableAssemble Fence To Bed Install Cutter Head GuardAssembly Fence Nut Mount Fence Lock Knob Nut Washer 1/2 Actual Size NotCutter Head Guard Functional Check Adjusting Guard SpringAdjusting the Leveling Feet Pan Head Screw KnobDepth of Cut Handwheel Getting to Know Your Jointer/PlanerFence Sliding Knob Nameplate Model/Serial Fence Tilt Bevel KnobOn-Off Switch Cutter Knife Alignment/Adjustments AlignmentsCutter Knife Sharpening 11/16 Wide New Blade Second Cutting Ground Surface EdgeOutfeed Table Too High Result Outfeed Table AdjustmentChecking Outfeed Table Alignment Outfeed Table Too Low ResultAngle Gauge Use Adjusting Table GibsFence Tilt Use and Bevel Stop Adjustment Stop Screw BarSafety Instructions for Basic Jointer/Planer Operation Before Each UseFence Slide Lock Knob Bevel Lock Handle Push blocks and push sticks Always Use Push Blocks When Planing, Beveling Or ChamferingFeeding the Workpiece All Operations Plan your workInspect your workpiece Before Leaving the jointer/planerStop Pin Operation Basic Jointer/Planer Cutting OperationsDepth of Cut Handwheel Operation Feeding the WorkpieceBeveling/Chamfering PlaningJointing Jointing Without Push BlocksSupport Long Workpieces Using the Hold-Down/Push-BlocksRabbeting Face Rabbet End EdgeSliding Fence Operation Sliding Lock KnobMaintenance Maintenance and LubricationWiring Diagram LubricationTroubleshooting Guide GeneralTrouble Probable Cause Remedy Motor Repair Parts Parts List for Ridgid 6-1/8 Jointer/Planer Model No. JP06101Always order by Part Number Not by Key Number Description Key DescriptionRepair Parts Repair Parts Repair Parts Repair Parts Repair Parts JEG6 DAY Satisfaction Guarantee Policy Call