RIDGID JP06101 Installing the Pulley Guard, Installing Handwheel, Serr 3/16-24 x 3/8 Belt Guard

Page 16

Assembly (continued)

Installing the Pulley Guard

1.From the hardware pack locate the following: From among the loose parts find the following:

4 Pan Head Cross Serrated Screws 3/16-24 x 3/8" Belt Guard

2.With assistance set the jointer upright.

3.Mount the belt guard in place as shown using the four 3/16" screws.

Screw Pan Head Cr

 

Serr 3/16-24 x 3/8"

Belt Guard

 

NOTE: Fence mount removed for clarity

Installing Handwheel

1.

From the hardware pack find the following:

 

 

 

 

1

Screw Pan Head 1/4-20 x 5/8

 

 

 

 

1

Washer 1/4

 

 

 

 

Screw Pan Head w/Washer

2.

From among the loose parts find the following:

1/4-20 x 5/8"

 

 

Handwheel

1 Handwheel

3.Slip the handwheel onto the infeed table elevation shaft and install the washer and screw as shown.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 235$725·60$18$ Table of Contents Safety Instructions For Jointer/PlanerBefore Using the Jointer/Planer Major HazardsSafety Labels and Indicators on the Jointer/Planer Plan Ahead To Protect Your Eyes, Hands, Face and Ears Inspect Your WorkpieceWhenever Jointer/Planer Is Running Before Leaving the Jointer/PlanerKeep Children Away Don’t Force ToolPower Supply and Motor Specifications Motor Specifications and Electrical RequirementsGlossary of Terms for Woodworking General Electrical Connections Volt, 60 Hz. Tool InformationChanging Motor Voltage Prong Plug Properly Grounded Outlet GroundingWire Sizes Motor Safety ProtectionExtension Gauge A.W.G Cord Length Unpacking and Checking Contents Loose Parts Hex Nut Loose Parts From Hardware PackHex Nut 16-18 Assembly Cabinet and Motor Mount AssemblyMotor Assembly with Switch Install the Leveling FeetMounting the Motor Tensioning Belt and Installing Rear Panel Mounting Jointer Table to CabinetBelt Align Belt Tighten Motor Mount NutsInstalling the Pulley Guard Installing HandwheelSerr 3/16-24 x 3/8 Belt Guard 20 x 5/8Adjusting Table Extension Attach Sawdust ChuteTool Storage Sawdust Chute Screw Wing 1/4-20 x 1/2 Outfeed Socket Head Screw Extension even with Outfeed tableInstall Cutter Head Guard Assembly Fence Nut MountAssemble Fence To Bed Fence Lock Knob Nut Washer 1/2 Actual Size NotAdjusting Guard Spring Adjusting the Leveling FeetCutter Head Guard Functional Check Pan Head Screw KnobGetting to Know Your Jointer/Planer Fence Sliding KnobDepth of Cut Handwheel Nameplate Model/Serial Fence Tilt Bevel KnobOn-Off Switch Cutter Knife Alignment/Adjustments AlignmentsCutter Knife Sharpening 11/16 Wide New Blade Second Cutting Ground Surface EdgeOutfeed Table Adjustment Checking Outfeed Table AlignmentOutfeed Table Too High Result Outfeed Table Too Low ResultAdjusting Table Gibs Fence Tilt Use and Bevel Stop AdjustmentAngle Gauge Use Stop Screw BarBefore Each Use Safety Instructions for Basic Jointer/Planer OperationFence Slide Lock Knob Bevel Lock Handle Always Use Push Blocks When Planing, Beveling Or Chamfering Feeding the Workpiece All OperationsPush blocks and push sticks Plan your workInspect your workpiece Before Leaving the jointer/planerBasic Jointer/Planer Cutting Operations Depth of Cut Handwheel OperationStop Pin Operation Feeding the WorkpiecePlaning JointingBeveling/Chamfering Jointing Without Push BlocksUsing the Hold-Down/Push-Blocks RabbetingSupport Long Workpieces Face Rabbet End EdgeSliding Fence Operation Sliding Lock KnobMaintenance and Lubrication Wiring DiagramMaintenance LubricationGeneral Troubleshooting GuideTrouble Probable Cause Remedy Motor Repair Parts Parts List for Ridgid 6-1/8 Jointer/Planer Model No. JP06101Always order by Part Number Not by Key Number Description Key DescriptionRepair Parts Repair Parts Repair Parts Repair Parts Repair Parts JEG6 DAY Satisfaction Guarantee Policy Call
Top Page Image Contents