RIDGID JP06101 manual Glossary of Terms for Woodworking, Power Supply and Motor Specifications

Page 7

Glossary of Terms for Woodworking

Bed

The combination of infeed and outfeed table surfaces which support the workpiece during a cutting operation.

Bevel/Chamfer

Removing wood along the edge of a board to make that edge straight, smooth and angled to the board face which is against the fence.

Cutter Guard

Spring loaded guard or shield covering the cutter head.

Cutter Head

The cutter head is a rotating piece with three adjustable knives. The cutter head removes material from the work- piece

Depth of cut

A term used to indicate how deep into the workpiece the cutter knives will cut.

Fence

The fence is attached to the jointer/planer base. The fence helps support and guide the workpiece as it is pushed across the cutter head.

Freehand

Using the tool without holding the workpiece firmly against the fence and table. This can let the workpiece twist and kick back and must never be attempted.

Gum

A sticky, sap based residue from wood products.

Hold-Down/Push-Blocks

They are required for your own safety. They are used to hold your workpieces against the table and fence when planing, rabbeting or jointing.

Infeed Table

The section of the jointer bed upon which the workpiece is placed before being pushed into the cutter head. Infeed table height is adjustable which allows the opera- tor to select the depth of cut.

Jointing

The removal of wood along the edge of a board so as to make that edge straight, smooth and square to the board face which is against the fence.

Kickback

An uncontrolled grabbing and throwing of the workpiece back toward the operator by the rotating cutter head.

Leading End

The end of the workpiece which is pushed into the cutter head first.

Outfeed Table

The section of a jointer bed which supports the workpiece after it passes over the cutter head.

Planing

Removing wood from the widest surface or face of a board so as to make it flat and smooth.

Rabbet

A notch cut into the edge of workpiece.

Resin

A sticky, sap based substance that has hardened.

Revolutions Per Minute (RPM)

The number of turns completed by a spinning object in one minute.

Throw-Back

Throwing of pieces in a manner similar to a kickback.

Trailing End

The workpiece end last cut by the knives.

Workpiece

The item on which the cutting operation is being per- formed. The surfaces of a workpiece are commonly referred to as faces, ends and edges.

Face

Rabbet

Edge End

Motor Specifications and Electrical Requirements

Power Supply and Motor Specifications

WARNING: To reduce the risk of electrical hazards, fire hazards or damage to the tool, use proper circuit protection. Your tool is wired at the factory for opera- tion using the voltage shown. Connect tool to a power line with the appropriate voltage and a 15-amp branch circuit. Use a 15-amp time delay type fuse or circuit breaker. To reduce the risk of shock or fire, if power cord is worn or cut, or damaged in any way, have it replaced immediately.

The A/C motor used on this tool is a capacitor start, non- reversible type, wired at the factory for 110-120V AC, 60 Hz. operation. Follow the instructions on page 8 to connect the motor for 220-240V A/C operation.

Rated Horsepower

 

1

 

 

 

Voltage

110-120

 

220-240

 

 

 

 

Amperes

12

 

6

 

 

 

 

Hertz (Cycles)

 

60

 

 

 

Phase

 

Single

 

 

 

RPM

 

3450

 

 

Rotation of Shaft

Counterclockwise

 

 

 

 

7

Image 7
Contents 235$725·60$18$ Safety Instructions For Jointer/Planer Table of ContentsMajor Hazards Before Using the Jointer/PlanerSafety Labels and Indicators on the Jointer/Planer Inspect Your Workpiece Plan Ahead To Protect Your Eyes, Hands, Face and EarsDon’t Force Tool Whenever Jointer/Planer Is RunningBefore Leaving the Jointer/Planer Keep Children AwayPower Supply and Motor Specifications Motor Specifications and Electrical RequirementsGlossary of Terms for Woodworking Prong Plug Properly Grounded Outlet Grounding General Electrical ConnectionsVolt, 60 Hz. Tool Information Changing Motor VoltageWire Sizes Motor Safety ProtectionExtension Gauge A.W.G Cord Length Unpacking and Checking Contents Loose Parts Hex Nut Loose Parts From Hardware PackHex Nut 16-18 Cabinet and Motor Mount Assembly AssemblyMotor Assembly with Switch Install the Leveling FeetMounting the Motor Align Belt Tighten Motor Mount Nuts Tensioning Belt and Installing Rear PanelMounting Jointer Table to Cabinet Belt20 x 5/8 Installing the Pulley GuardInstalling Handwheel Serr 3/16-24 x 3/8 Belt GuardOutfeed Socket Head Screw Extension even with Outfeed table Adjusting Table ExtensionAttach Sawdust Chute Tool Storage Sawdust Chute Screw Wing 1/4-20 x 1/2Fence Lock Knob Nut Washer 1/2 Actual Size Not Install Cutter Head GuardAssembly Fence Nut Mount Assemble Fence To BedPan Head Screw Knob Adjusting Guard SpringAdjusting the Leveling Feet Cutter Head Guard Functional CheckNameplate Model/Serial Fence Tilt Bevel Knob Getting to Know Your Jointer/PlanerFence Sliding Knob Depth of Cut HandwheelOn-Off Switch Alignments Cutter Knife Alignment/Adjustments11/16 Wide New Blade Second Cutting Ground Surface Edge Cutter Knife SharpeningOutfeed Table Too Low Result Outfeed Table AdjustmentChecking Outfeed Table Alignment Outfeed Table Too High ResultStop Screw Bar Adjusting Table GibsFence Tilt Use and Bevel Stop Adjustment Angle Gauge UseBefore Each Use Safety Instructions for Basic Jointer/Planer OperationFence Slide Lock Knob Bevel Lock Handle Plan your work Always Use Push Blocks When Planing, Beveling Or ChamferingFeeding the Workpiece All Operations Push blocks and push sticksBefore Leaving the jointer/planer Inspect your workpieceFeeding the Workpiece Basic Jointer/Planer Cutting OperationsDepth of Cut Handwheel Operation Stop Pin OperationJointing Without Push Blocks PlaningJointing Beveling/ChamferingFace Rabbet End Edge Using the Hold-Down/Push-BlocksRabbeting Support Long WorkpiecesSliding Lock Knob Sliding Fence OperationLubrication Maintenance and LubricationWiring Diagram MaintenanceGeneral Troubleshooting GuideTrouble Probable Cause Remedy Motor Parts List for Ridgid 6-1/8 Jointer/Planer Model No. JP06101 Repair PartsKey Description Always order by Part Number Not by Key Number DescriptionRepair Parts Repair Parts Repair Parts Repair Parts Repair Parts JEG6 Call DAY Satisfaction Guarantee Policy