RIDGID JP06101 manual Attach Sawdust Chute, Adjusting Table Extension

Page 17

Attach Sawdust Chute

1.From among the loose parts find the following:

1Sawdust Chute

2Wing Screw 1/4-20 x 1/2

1Wrench Box 8mm/10mm

1Wrench Hex-“L” 3mm

2.Slide the tab on the bottom side of the dust chute into the slot just below the chute on the left side of the base. Fasten the dust chute on with the 2 wing screws through the slots on both sides of the dust chute.

3.The 3mm hex-L wrench and 8mm open end wrench (supplied with the jointer) used for blade adjustments, can be conveniently stored in the dust chute as shown.

NOTE: If a dust collection system is not in use, simply loosen the two wing screws, lift the bottom of the chute up, out and then slide the dust chute up and retighten the wing screws.

Tool

Storage

Sawdust Chute

Screw Wing 1/4-20 x 1/2

Adjusting Table Extension

The table extension is adjusted at the factory and should not require any additional adjustments. In the event that it shifted during shipping, align it to the outfeed table as fol- lows.

1.Loosen the 2 hex head screws that attach the exten- sion to the outfeed table.

2.Using a straight edge, align the extension to be flush with the outfeed table.

3.Tighten the two screws and recheck the alignment.

Outfeed

Table

Socket Head

Screw

	Extension even with
Extension	outfeed table
Extension

17

Image 17

Contents 235$725·60$18$ Safety Instructions For Jointer/Planer Table of ContentsMajor Hazards Before Using the Jointer/PlanerSafety Labels and Indicators on the Jointer/Planer Inspect Your Workpiece Plan Ahead To Protect Your Eyes, Hands, Face and EarsBefore Leaving the Jointer/Planer Whenever Jointer/Planer Is RunningKeep Children Away Don’t Force ToolGlossary of Terms for Woodworking Motor Specifications and Electrical RequirementsPower Supply and Motor Specifications Volt, 60 Hz. Tool Information General Electrical ConnectionsChanging Motor Voltage Prong Plug Properly Grounded Outlet GroundingExtension Gauge A.W.G Cord Length Motor Safety ProtectionWire Sizes Unpacking and Checking Contents Loose Parts Hex Nut 16-18 Loose Parts From Hardware PackHex Nut Cabinet and Motor Mount Assembly AssemblyMounting the Motor Install the Leveling FeetMotor Assembly with Switch Mounting Jointer Table to Cabinet Tensioning Belt and Installing Rear PanelBelt Align Belt Tighten Motor Mount NutsInstalling Handwheel Installing the Pulley GuardSerr 3/16-24 x 3/8 Belt Guard 20 x 5/8Attach Sawdust Chute Adjusting Table ExtensionTool Storage Sawdust Chute Screw Wing 1/4-20 x 1/2 Outfeed Socket Head Screw Extension even with Outfeed tableAssembly Fence Nut Mount Install Cutter Head GuardAssemble Fence To Bed Fence Lock Knob Nut Washer 1/2 Actual Size NotAdjusting the Leveling Feet Adjusting Guard SpringCutter Head Guard Functional Check Pan Head Screw KnobFence Sliding Knob Getting to Know Your Jointer/PlanerDepth of Cut Handwheel Nameplate Model/Serial Fence Tilt Bevel KnobOn-Off Switch Alignments Cutter Knife Alignment/Adjustments11/16 Wide New Blade Second Cutting Ground Surface Edge Cutter Knife SharpeningChecking Outfeed Table Alignment Outfeed Table AdjustmentOutfeed Table Too High Result Outfeed Table Too Low ResultFence Tilt Use and Bevel Stop Adjustment Adjusting Table GibsAngle Gauge Use Stop Screw BarFence Slide Lock Knob Bevel Lock Handle Safety Instructions for Basic Jointer/Planer OperationBefore Each Use Feeding the Workpiece All Operations Always Use Push Blocks When Planing, Beveling Or ChamferingPush blocks and push sticks Plan your workBefore Leaving the jointer/planer Inspect your workpieceDepth of Cut Handwheel Operation Basic Jointer/Planer Cutting OperationsStop Pin Operation Feeding the WorkpieceJointing PlaningBeveling/Chamfering Jointing Without Push BlocksRabbeting Using the Hold-Down/Push-BlocksSupport Long Workpieces Face Rabbet End EdgeSliding Lock Knob Sliding Fence OperationWiring Diagram Maintenance and LubricationMaintenance LubricationTrouble Probable Cause Remedy Troubleshooting GuideGeneral Motor Parts List for Ridgid 6-1/8 Jointer/Planer Model No. JP06101 Repair PartsKey Description Always order by Part Number Not by Key Number DescriptionRepair Parts Repair Parts Repair Parts Repair Parts Repair Parts JEG6 Call DAY Satisfaction Guarantee Policy