RIDGID JP06101 Cutter Knife Sharpening, 11/16 Wide New Blade Second Cutting Ground Surface Edge

Page 23

Cutter Knife Sharpening

The knives can be honed individually with an ordinary oil- stone.

Make sure your oilstone is not worn in the center. It must be flat.

Be sure to remove the burr on the flat side.

WARNING: The cutter knives are extremely sharp. Do not let your hand or fingers touch the cutter knives.

If the knives are nicked they must be replaced or reground. They can be reground several times until they become 9/16" wide. Never install unbalanced knives or reground knives less than 9/16" wide.

Have your knives reground by someone who is compe- tent. Look under “Sharpening Services” in the “Yellow Pages” of your telephone directory.

NOTE: The knives may have a second, very small ground surface very close to the sharpened edge of the blade. Hone only the edge of the blade which will be doing the cutting.

38°

11/16 In

Wide

New Blade

		Second
	Cutting	Ground
	Cutting	Surface
	Edge	Surface
	Edge

Image 23

Contents 235$725·60$18$ Safety Instructions For Jointer/Planer Table of ContentsMajor Hazards Before Using the Jointer/PlanerSafety Labels and Indicators on the Jointer/Planer Inspect Your Workpiece Plan Ahead To Protect Your Eyes, Hands, Face and EarsDon’t Force Tool Whenever Jointer/Planer Is RunningBefore Leaving the Jointer/Planer Keep Children AwayGlossary of Terms for Woodworking Motor Specifications and Electrical RequirementsPower Supply and Motor Specifications Prong Plug Properly Grounded Outlet Grounding General Electrical ConnectionsVolt, 60 Hz. Tool Information Changing Motor VoltageExtension Gauge A.W.G Cord Length Motor Safety ProtectionWire Sizes Unpacking and Checking Contents Loose Parts Hex Nut 16-18 Loose Parts From Hardware PackHex Nut Cabinet and Motor Mount Assembly AssemblyMounting the Motor Install the Leveling FeetMotor Assembly with Switch Align Belt Tighten Motor Mount Nuts Tensioning Belt and Installing Rear PanelMounting Jointer Table to Cabinet Belt20 x 5/8 Installing the Pulley GuardInstalling Handwheel Serr 3/16-24 x 3/8 Belt GuardOutfeed Socket Head Screw Extension even with Outfeed table Adjusting Table ExtensionAttach Sawdust Chute Tool Storage Sawdust Chute Screw Wing 1/4-20 x 1/2Fence Lock Knob Nut Washer 1/2 Actual Size Not Install Cutter Head GuardAssembly Fence Nut Mount Assemble Fence To BedPan Head Screw Knob Adjusting Guard SpringAdjusting the Leveling Feet Cutter Head Guard Functional CheckNameplate Model/Serial Fence Tilt Bevel Knob Getting to Know Your Jointer/PlanerFence Sliding Knob Depth of Cut HandwheelOn-Off Switch Alignments Cutter Knife Alignment/Adjustments11/16 Wide New Blade Second Cutting Ground Surface Edge Cutter Knife SharpeningOutfeed Table Too Low Result Outfeed Table AdjustmentChecking Outfeed Table Alignment Outfeed Table Too High ResultStop Screw Bar Adjusting Table GibsFence Tilt Use and Bevel Stop Adjustment Angle Gauge UseFence Slide Lock Knob Bevel Lock Handle Safety Instructions for Basic Jointer/Planer OperationBefore Each Use Plan your work Always Use Push Blocks When Planing, Beveling Or ChamferingFeeding the Workpiece All Operations Push blocks and push sticksBefore Leaving the jointer/planer Inspect your workpieceFeeding the Workpiece Basic Jointer/Planer Cutting OperationsDepth of Cut Handwheel Operation Stop Pin OperationJointing Without Push Blocks PlaningJointing Beveling/ChamferingFace Rabbet End Edge Using the Hold-Down/Push-BlocksRabbeting Support Long WorkpiecesSliding Lock Knob Sliding Fence OperationLubrication Maintenance and LubricationWiring Diagram MaintenanceTrouble Probable Cause Remedy Troubleshooting GuideGeneral Motor Parts List for Ridgid 6-1/8 Jointer/Planer Model No. JP06101 Repair PartsKey Description Always order by Part Number Not by Key Number DescriptionRepair Parts Repair Parts Repair Parts Repair Parts Repair Parts JEG6 Call DAY Satisfaction Guarantee Policy