RIDGID JP06101 manual Assemble Fence To Bed, Install Cutter Head Guard, Assembly Fence Nut Mount

Page 18

Assembly (continued)

Assemble Fence To Bed

1. From the hardware pack find the following:
1	Washer 1/2"
1	T-Nut
From among the loose parts find the following
1	Fence Assembly

Fence Lock Knob

T-Nut

Washer 1/2" (Actual Size Not

	1	Fence Lock Knob
	1	Fence Tilt Knob
2.	Position fence onto fence support as shown making
	sure the keyway in fence assembly lines up with the
	key on the fence mount.
3.	Once fence is in place, slide the fence lock knob
	through the 1/2" washer and then through the fence
	assembly and fence mount. Thread T-nut onto the end
	of the lock knob. Make sure the tabs on the nut sit in
	the slot on the fence mount.
4.	Slide the fence back and fourth to make sure it moves
	freely. Then lock in place.
5.	Thread the fence tilt knob into the fence.

(Actual Size Not Shown) Shown)

Fence Assembly

Fence Tilt Knob

Fence Lock

Knob

Fence	Washer
Assembly

Fence		T-Nut
Fence		T-Nut
Mount

Install Cutter Head Guard

1.From among the loose parts find the cutter head guard. Remove the pan head screw from the bottom of the guard post.

2.Turn the spring-loaded knob 1 turn counterclockwise, looking down through the hole in the infeed table.

3.Line the slot in the guard post with the pin in the knob. Slide the post through table and over pin in the knob.

4.Reinstall the pan head screw in the bottom of the guard post.

NOTE: The two ribs on top of the fence indicate where the cutter head opening is located in the table.

Cutter Head

Guard

Slot

Spring Loaded

Knob

Cutter Head

Opening Indicators

18

Image 18

Contents 235$725·60$18$ Table of Contents Safety Instructions For Jointer/PlanerBefore Using the Jointer/Planer Major HazardsSafety Labels and Indicators on the Jointer/Planer Plan Ahead To Protect Your Eyes, Hands, Face and Ears Inspect Your WorkpieceKeep Children Away Whenever Jointer/Planer Is RunningBefore Leaving the Jointer/Planer Don’t Force ToolMotor Specifications and Electrical Requirements Power Supply and Motor SpecificationsGlossary of Terms for Woodworking Changing Motor Voltage General Electrical ConnectionsVolt, 60 Hz. Tool Information Prong Plug Properly Grounded Outlet GroundingMotor Safety Protection Wire SizesExtension Gauge A.W.G Cord Length Unpacking and Checking Contents Loose Parts Loose Parts From Hardware Pack Hex NutHex Nut 16-18 Assembly Cabinet and Motor Mount AssemblyInstall the Leveling Feet Motor Assembly with SwitchMounting the Motor Belt Tensioning Belt and Installing Rear PanelMounting Jointer Table to Cabinet Align Belt Tighten Motor Mount NutsSerr 3/16-24 x 3/8 Belt Guard Installing the Pulley GuardInstalling Handwheel 20 x 5/8Tool Storage Sawdust Chute Screw Wing 1/4-20 x 1/2 Adjusting Table ExtensionAttach Sawdust Chute Outfeed Socket Head Screw Extension even with Outfeed tableAssemble Fence To Bed Install Cutter Head GuardAssembly Fence Nut Mount Fence Lock Knob Nut Washer 1/2 Actual Size NotCutter Head Guard Functional Check Adjusting Guard SpringAdjusting the Leveling Feet Pan Head Screw KnobDepth of Cut Handwheel Getting to Know Your Jointer/PlanerFence Sliding Knob Nameplate Model/Serial Fence Tilt Bevel KnobOn-Off Switch Cutter Knife Alignment/Adjustments AlignmentsCutter Knife Sharpening 11/16 Wide New Blade Second Cutting Ground Surface EdgeOutfeed Table Too High Result Outfeed Table AdjustmentChecking Outfeed Table Alignment Outfeed Table Too Low ResultAngle Gauge Use Adjusting Table GibsFence Tilt Use and Bevel Stop Adjustment Stop Screw BarSafety Instructions for Basic Jointer/Planer Operation Before Each UseFence Slide Lock Knob Bevel Lock Handle Push blocks and push sticks Always Use Push Blocks When Planing, Beveling Or ChamferingFeeding the Workpiece All Operations Plan your workInspect your workpiece Before Leaving the jointer/planerStop Pin Operation Basic Jointer/Planer Cutting OperationsDepth of Cut Handwheel Operation Feeding the WorkpieceBeveling/Chamfering PlaningJointing Jointing Without Push BlocksSupport Long Workpieces Using the Hold-Down/Push-BlocksRabbeting Face Rabbet End EdgeSliding Fence Operation Sliding Lock KnobMaintenance Maintenance and LubricationWiring Diagram LubricationTroubleshooting Guide GeneralTrouble Probable Cause Remedy Motor Repair Parts Parts List for Ridgid 6-1/8 Jointer/Planer Model No. JP06101Always order by Part Number Not by Key Number Description Key DescriptionRepair Parts Repair Parts Repair Parts Repair Parts Repair Parts JEG6 DAY Satisfaction Guarantee Policy Call