RIDGID JP06101 manual On-Off Switch

Page 21

15. Angle Gauge

Used to set the fence at the proper angle.

WARNING: Before turning switch “ON”, make sure the blade guard is correctly installed and operating properly to prevent serious personal injury.

16.On-Off Switch

Turns the tool on and off. The “yellow button” is a key. When it is inserted in the switch lever, the power may be turned ON and OFF. When it is removed, the power cannot be turned ON. This feature is intended to help prevent unauthorized and possible hazardous use by children and others.

The on-off switch is shaped to make turning it ON accidentally less likely.

In an emergency, it can be turned OFF by striking it with the palm of the hand.

•Insert key into switch.

•To turn the tool “On”, insert finger under the switch lever and pull end of lever out.

•To turn the tool “Off”, push the lever in. Never leave the tool unattended until it has come to a complete stop.

•To lock the switch in the “Off” position, hold the switch in with one hand and remove the key with the other hand as shown.

WARNING: To prevent unauthorized use always lock the switch “OFF” when jointer/planer is not in use. Remove key and keep it in a safe place to prevent serious personal injury. In the event of a power failure, turn switch off. Lock it and remove the key. This will prevent the jointer/planer from starting up again when the power comes back on.

21

Image 21

Contents 235$725·60$18$ Safety Instructions For Jointer/Planer Table of ContentsMajor Hazards Before Using the Jointer/PlanerSafety Labels and Indicators on the Jointer/Planer Inspect Your Workpiece Plan Ahead To Protect Your Eyes, Hands, Face and EarsBefore Leaving the Jointer/Planer Whenever Jointer/Planer Is RunningKeep Children Away Don’t Force ToolMotor Specifications and Electrical Requirements Power Supply and Motor SpecificationsGlossary of Terms for Woodworking Volt, 60 Hz. Tool Information General Electrical ConnectionsChanging Motor Voltage Prong Plug Properly Grounded Outlet GroundingMotor Safety Protection Wire SizesExtension Gauge A.W.G Cord Length Unpacking and Checking Contents Loose Parts Loose Parts From Hardware Pack Hex NutHex Nut 16-18 Cabinet and Motor Mount Assembly AssemblyInstall the Leveling Feet Motor Assembly with SwitchMounting the Motor Mounting Jointer Table to Cabinet Tensioning Belt and Installing Rear PanelBelt Align Belt Tighten Motor Mount NutsInstalling Handwheel Installing the Pulley GuardSerr 3/16-24 x 3/8 Belt Guard 20 x 5/8Attach Sawdust Chute Adjusting Table ExtensionTool Storage Sawdust Chute Screw Wing 1/4-20 x 1/2 Outfeed Socket Head Screw Extension even with Outfeed tableAssembly Fence Nut Mount Install Cutter Head GuardAssemble Fence To Bed Fence Lock Knob Nut Washer 1/2 Actual Size NotAdjusting the Leveling Feet Adjusting Guard SpringCutter Head Guard Functional Check Pan Head Screw KnobFence Sliding Knob Getting to Know Your Jointer/PlanerDepth of Cut Handwheel Nameplate Model/Serial Fence Tilt Bevel KnobOn-Off Switch Alignments Cutter Knife Alignment/Adjustments11/16 Wide New Blade Second Cutting Ground Surface Edge Cutter Knife SharpeningChecking Outfeed Table Alignment Outfeed Table AdjustmentOutfeed Table Too High Result Outfeed Table Too Low ResultFence Tilt Use and Bevel Stop Adjustment Adjusting Table GibsAngle Gauge Use Stop Screw BarSafety Instructions for Basic Jointer/Planer Operation Before Each UseFence Slide Lock Knob Bevel Lock Handle Feeding the Workpiece All Operations Always Use Push Blocks When Planing, Beveling Or ChamferingPush blocks and push sticks Plan your workBefore Leaving the jointer/planer Inspect your workpieceDepth of Cut Handwheel Operation Basic Jointer/Planer Cutting OperationsStop Pin Operation Feeding the WorkpieceJointing PlaningBeveling/Chamfering Jointing Without Push BlocksRabbeting Using the Hold-Down/Push-BlocksSupport Long Workpieces Face Rabbet End EdgeSliding Lock Knob Sliding Fence OperationWiring Diagram Maintenance and LubricationMaintenance LubricationTroubleshooting Guide GeneralTrouble Probable Cause Remedy Motor Parts List for Ridgid 6-1/8 Jointer/Planer Model No. JP06101 Repair PartsKey Description Always order by Part Number Not by Key Number DescriptionRepair Parts Repair Parts Repair Parts Repair Parts Repair Parts JEG6 Call DAY Satisfaction Guarantee Policy