RIDGID JP06101 manual Cabinet and Motor Mount Assembly

Page 13

Assembly

WARNING: This tool is heavy. To reduce the risk of back injury, get help whenever you have to lift the tool.

Cabinet and Motor Mount Assembly

1.From the hardware pack find the following:

6Carriage Head Bolts 5/16-18 x 1/2"

6Serrated Flange Hex Nut 5/16

From among the loose parts find the following: Left Panel Side

Right Panel Side Motor Mount

2.Mount the motor mount onto the left side panel as shown. Make sure the lower tab of the motor mount with two holes is on the inside of the left side panel . Bolt the motor mount to the panel using the 5/16 car- riage head bolts and 5/16 serrated flange nuts. Tighten the nuts with a wrench.

3.Mount the right side panel to the motor mount as shown using two 5/16 carriage head bolts and 5/16 serrated flange nuts. Tighten the nuts with a wrench.

4.From the hardware pack find the following:

6Carriage Head Bolts 5/16-18 x 1/2"

6Serrated Flange Hex Nuts 5/16

From among the loose parts find the following:

1Front panel with RIDGID label

5.Bolt the front panel in place as shown using six 5/16 car- riage head bolts and six 5/16 serrated flange nuts. Make sure the front panel is mounted on the same side of the base as the switch opening. The panel should bolt in place on the backside of the left and right side panels as shown. Tighten the nuts with a wrench.

6.Tighten all bolts on the base at this time.

NOTE: It may be easier to tighten the bolt holding the front panel on if the base is turned on its side. The rear panel will be mounted later.

NOTE: Holes marked “A” on both front and rear panels are not used for assembly .

A

A

Front Panel

Carriage Head Bolt

5/16-18 x 1/2"

Motor Mount

Bracket

Serrated Flange

Hex Nut 5/16

Left Side

Panel

Right Side

Panel

Switch

Opening

Cabinet Front

13

Image 13

Contents 235$725·60$18$ Safety Instructions For Jointer/Planer Table of ContentsMajor Hazards Before Using the Jointer/PlanerSafety Labels and Indicators on the Jointer/Planer Inspect Your Workpiece Plan Ahead To Protect Your Eyes, Hands, Face and EarsBefore Leaving the Jointer/Planer Whenever Jointer/Planer Is RunningKeep Children Away Don’t Force ToolPower Supply and Motor Specifications Motor Specifications and Electrical RequirementsGlossary of Terms for Woodworking Volt, 60 Hz. Tool Information General Electrical ConnectionsChanging Motor Voltage Prong Plug Properly Grounded Outlet GroundingWire Sizes Motor Safety ProtectionExtension Gauge A.W.G Cord Length Unpacking and Checking Contents Loose Parts Hex Nut Loose Parts From Hardware PackHex Nut 16-18 Cabinet and Motor Mount Assembly AssemblyMotor Assembly with Switch Install the Leveling FeetMounting the Motor Mounting Jointer Table to Cabinet Tensioning Belt and Installing Rear PanelBelt Align Belt Tighten Motor Mount NutsInstalling Handwheel Installing the Pulley GuardSerr 3/16-24 x 3/8 Belt Guard 20 x 5/8Attach Sawdust Chute Adjusting Table ExtensionTool Storage Sawdust Chute Screw Wing 1/4-20 x 1/2 Outfeed Socket Head Screw Extension even with Outfeed tableAssembly Fence Nut Mount Install Cutter Head GuardAssemble Fence To Bed Fence Lock Knob Nut Washer 1/2 Actual Size NotAdjusting the Leveling Feet Adjusting Guard SpringCutter Head Guard Functional Check Pan Head Screw KnobFence Sliding Knob Getting to Know Your Jointer/PlanerDepth of Cut Handwheel Nameplate Model/Serial Fence Tilt Bevel KnobOn-Off Switch Alignments Cutter Knife Alignment/Adjustments11/16 Wide New Blade Second Cutting Ground Surface Edge Cutter Knife SharpeningChecking Outfeed Table Alignment Outfeed Table AdjustmentOutfeed Table Too High Result Outfeed Table Too Low ResultFence Tilt Use and Bevel Stop Adjustment Adjusting Table GibsAngle Gauge Use Stop Screw BarBefore Each Use Safety Instructions for Basic Jointer/Planer OperationFence Slide Lock Knob Bevel Lock Handle Feeding the Workpiece All Operations Always Use Push Blocks When Planing, Beveling Or ChamferingPush blocks and push sticks Plan your workBefore Leaving the jointer/planer Inspect your workpieceDepth of Cut Handwheel Operation Basic Jointer/Planer Cutting OperationsStop Pin Operation Feeding the WorkpieceJointing PlaningBeveling/Chamfering Jointing Without Push BlocksRabbeting Using the Hold-Down/Push-BlocksSupport Long Workpieces Face Rabbet End EdgeSliding Lock Knob Sliding Fence OperationWiring Diagram Maintenance and LubricationMaintenance LubricationGeneral Troubleshooting GuideTrouble Probable Cause Remedy Motor Parts List for Ridgid 6-1/8 Jointer/Planer Model No. JP06101 Repair PartsKey Description Always order by Part Number Not by Key Number DescriptionRepair Parts Repair Parts Repair Parts Repair Parts Repair Parts JEG6 Call DAY Satisfaction Guarantee Policy