RIDGID JP06101 Getting to Know Your Jointer/Planer, Fence Sliding Knob, Depth of Cut Handwheel

Page 20

Getting to Know Your Jointer/Planer

7 Fence Stops

	8 Nameplate
	Model/Serial
	9 Fence Tilt
6 Depth of Cut	(Bevel) Handle
6 Depth of Cut
Handwheel	Outfeed Table
5 Table	Handwheel
5 Table
Lock Screw
4 Belt Guard	11 Fence Tilt	10 Fence
	Knob

3 Fence Sliding

Knob

12 Infeed Table

2 Outfeed

Table

1 Dust

Chute

WARNING: For your own safety turn switch “OFF” and remove plug from power source outlet before making any adjustments.

1.Dust Chute with Tool Storage

Allows 4" diameter dust collection hose. Easily slides up and out of the way when a vacuum is not con- nected. Also tool storage for blade adjustment wrenches.

2.Outfeed Table

The section of a jointer bed which supports the work- piece after it passes over the cutter.

3.Fence Sliding Knob

Allows fence to move across table front to back. This is done to achieve full width of cut or to use a different (sharper) part of blade.

4.Belt Guard

Protects user from incidental access to the motor belt and pulley.

5.Table Lock Screw - When desired, use these screws to lock infeed or outfeed table at a desired height.

6.Depth of Cut Handwheel

By turning the handwheel you can control how much wood will be removed from the workpiece on each cut.

13 Cutter Head

Guard

Depth Indicator

14 Stop Pin

16 On-Off

Switch

15 Angle Gauge

7.Fence Stops

When adjusted properly, these stops provide a method for quickly moving the fence to a 90°, 45° or 135° position from the table.

8.Nameplate Model/Serial

9.Fence Tilt (Bevel) Knob

Locks fence in various bevel positions.

10.Fence - Guides workpiece over cutter head.

11.Fence Tilt Knob - Used to adjust fence angle posi- tion.

12.Infeed Table

The section of the jointer bed upon which the work- piece is placed before being pushed into the cutter. Its height is adjustable which allows the operator to select the depth of cut.

13.Cutter Head Guard

Helps protect the operator from the sharp knives on the cutterhead. It is spring loaded so it automatically keeps the cutterhead covered before, during, and after a cutting operation. It must always be used.

14.Stop Pin

For rabbeting operations greater than 1/8" deep, pin can be pulled out to lower infeed table in 1/8" incre- ments.

20

Image 20

Contents 235$725·60$18$ Table of Contents Safety Instructions For Jointer/PlanerBefore Using the Jointer/Planer Major HazardsSafety Labels and Indicators on the Jointer/Planer Plan Ahead To Protect Your Eyes, Hands, Face and Ears Inspect Your WorkpieceWhenever Jointer/Planer Is Running Before Leaving the Jointer/PlanerKeep Children Away Don’t Force ToolGlossary of Terms for Woodworking Motor Specifications and Electrical RequirementsPower Supply and Motor Specifications General Electrical Connections Volt, 60 Hz. Tool InformationChanging Motor Voltage Prong Plug Properly Grounded Outlet GroundingExtension Gauge A.W.G Cord Length Motor Safety ProtectionWire Sizes Unpacking and Checking Contents Loose Parts Hex Nut 16-18 Loose Parts From Hardware PackHex Nut Assembly Cabinet and Motor Mount AssemblyMounting the Motor Install the Leveling FeetMotor Assembly with Switch Tensioning Belt and Installing Rear Panel Mounting Jointer Table to CabinetBelt Align Belt Tighten Motor Mount NutsInstalling the Pulley Guard Installing HandwheelSerr 3/16-24 x 3/8 Belt Guard 20 x 5/8Adjusting Table Extension Attach Sawdust ChuteTool Storage Sawdust Chute Screw Wing 1/4-20 x 1/2 Outfeed Socket Head Screw Extension even with Outfeed tableInstall Cutter Head Guard Assembly Fence Nut MountAssemble Fence To Bed Fence Lock Knob Nut Washer 1/2 Actual Size NotAdjusting Guard Spring Adjusting the Leveling FeetCutter Head Guard Functional Check Pan Head Screw KnobGetting to Know Your Jointer/Planer Fence Sliding KnobDepth of Cut Handwheel Nameplate Model/Serial Fence Tilt Bevel KnobOn-Off Switch Cutter Knife Alignment/Adjustments AlignmentsCutter Knife Sharpening 11/16 Wide New Blade Second Cutting Ground Surface EdgeOutfeed Table Adjustment Checking Outfeed Table AlignmentOutfeed Table Too High Result Outfeed Table Too Low ResultAdjusting Table Gibs Fence Tilt Use and Bevel Stop AdjustmentAngle Gauge Use Stop Screw BarFence Slide Lock Knob Bevel Lock Handle Safety Instructions for Basic Jointer/Planer OperationBefore Each Use Always Use Push Blocks When Planing, Beveling Or Chamfering Feeding the Workpiece All OperationsPush blocks and push sticks Plan your workInspect your workpiece Before Leaving the jointer/planerBasic Jointer/Planer Cutting Operations Depth of Cut Handwheel OperationStop Pin Operation Feeding the WorkpiecePlaning JointingBeveling/Chamfering Jointing Without Push BlocksUsing the Hold-Down/Push-Blocks RabbetingSupport Long Workpieces Face Rabbet End EdgeSliding Fence Operation Sliding Lock KnobMaintenance and Lubrication Wiring DiagramMaintenance LubricationTrouble Probable Cause Remedy Troubleshooting GuideGeneral Motor Repair Parts Parts List for Ridgid 6-1/8 Jointer/Planer Model No. JP06101Always order by Part Number Not by Key Number Description Key DescriptionRepair Parts Repair Parts Repair Parts Repair Parts Repair Parts JEG6 DAY Satisfaction Guarantee Policy Call