RIDGID JP06101 manual Alignments, Cutter Knife Alignment/Adjustments

Page 22

Alignments

Cutter Knife Alignment/Adjustments

WARNING: The cutter knives are extremely sharp. Do not let your hand or fingers touch the cutter knives to prevent serious personal injury.

Tools Needed

8mm open end wrench and 3mm Allen wrench (supplied). Metal straightedge

• Unplug jointer/planer.

WARNING: To reduce the risk of injury from acci- dental start, make sure switch is “OFF” and plug is not connected to power source outlet.

Checking Alignment

Note: The blades are adjusted at the factory, and should not require adjustment.

1.Lower infeed table by turning the depth of the cut handwheel clockwise.

2.Position the fence to the rear of the jointer, approxi- mately 1/4" beyond the end of the cutter knives. Lock the fence in this position.

3.Remove cutter head guard.

4.Place a straightedge on the outfeed table, extending over the cutter head as shown.

5.Adjust the outfeed table so that the straightedge just touches one of the knives as the cutter head is turned. Check one side of the knife then move the straight- edge and check the other side of the knife. If the knife lifts the straightedge or does not touch it, readjust the knife as necessary (see procedure below). Check all three blades this same way.

Blade Adjustment

1.Loosen knife lock screws using the 8mm wrench, turn- ing the wrench toward the fence. Remove all the parts and clean thoroughly with a gum and paste remover. Reinstall parts as shown, making sure the blade extends 1/16" past the cutter head as shown.

2.Place a straightedge as indicated in step 4 above. Position the straightedge over the end of one of the blades closest to the fence.

3.Rotate the cutter head so the knife that is being adjusted is at the highest point.

4.Adjust the jackscrew nearest to the straightedge so that the knife just touches the straightedge as the cut- ter head is rotated and there is no gap between the outfeed table and the straightedge.

5.Move the straightedge to the other end of the cutter head and repeat step 4 with the second jackscrew.

6.Tighten the four knife lock screws.

7.Repeat steps 1 through 6 for the other two knives.

Important: Turn the cutter head two full revolutions to make sure the cutter head turns freely and the blades clear the jointer bed.

8.Quickly recheck all three knives with the straightedge to ensure all knives are even and square.

WARNING: Read, understand and perform entire Alignment section before using the jointer/planer. Failure to heed this warning could result in serious

Straightedge

Outfeed

Infeed

Table

Table

 

Cutterhead

Jackscrew

Lock Screws

Wedge

Blade

Screws

Cutter

Head

1/16

 

 

 

Blade

 

 

 

 

 

 

 

 

Cutter Head

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents 235$725·60$18$ Table of Contents Safety Instructions For Jointer/PlanerBefore Using the Jointer/Planer Major HazardsSafety Labels and Indicators on the Jointer/Planer Plan Ahead To Protect Your Eyes, Hands, Face and Ears Inspect Your WorkpieceKeep Children Away Whenever Jointer/Planer Is RunningBefore Leaving the Jointer/Planer Don’t Force ToolPower Supply and Motor Specifications Motor Specifications and Electrical RequirementsGlossary of Terms for Woodworking Changing Motor Voltage General Electrical ConnectionsVolt, 60 Hz. Tool Information Prong Plug Properly Grounded Outlet GroundingWire Sizes Motor Safety ProtectionExtension Gauge A.W.G Cord Length Unpacking and Checking Contents Loose Parts Hex Nut Loose Parts From Hardware PackHex Nut 16-18 Assembly Cabinet and Motor Mount AssemblyMotor Assembly with Switch Install the Leveling FeetMounting the Motor Belt Tensioning Belt and Installing Rear PanelMounting Jointer Table to Cabinet Align Belt Tighten Motor Mount NutsSerr 3/16-24 x 3/8 Belt Guard Installing the Pulley GuardInstalling Handwheel 20 x 5/8Tool Storage Sawdust Chute Screw Wing 1/4-20 x 1/2 Adjusting Table ExtensionAttach Sawdust Chute Outfeed Socket Head Screw Extension even with Outfeed tableAssemble Fence To Bed Install Cutter Head GuardAssembly Fence Nut Mount Fence Lock Knob Nut Washer 1/2 Actual Size NotCutter Head Guard Functional Check Adjusting Guard SpringAdjusting the Leveling Feet Pan Head Screw KnobDepth of Cut Handwheel Getting to Know Your Jointer/PlanerFence Sliding Knob Nameplate Model/Serial Fence Tilt Bevel KnobOn-Off Switch Cutter Knife Alignment/Adjustments AlignmentsCutter Knife Sharpening 11/16 Wide New Blade Second Cutting Ground Surface EdgeOutfeed Table Too High Result Outfeed Table AdjustmentChecking Outfeed Table Alignment Outfeed Table Too Low ResultAngle Gauge Use Adjusting Table GibsFence Tilt Use and Bevel Stop Adjustment Stop Screw BarBefore Each Use Safety Instructions for Basic Jointer/Planer OperationFence Slide Lock Knob Bevel Lock Handle Push blocks and push sticks Always Use Push Blocks When Planing, Beveling Or ChamferingFeeding the Workpiece All Operations Plan your workInspect your workpiece Before Leaving the jointer/planerStop Pin Operation Basic Jointer/Planer Cutting OperationsDepth of Cut Handwheel Operation Feeding the WorkpieceBeveling/Chamfering PlaningJointing Jointing Without Push BlocksSupport Long Workpieces Using the Hold-Down/Push-BlocksRabbeting Face Rabbet End EdgeSliding Fence Operation Sliding Lock KnobMaintenance Maintenance and LubricationWiring Diagram LubricationGeneral Troubleshooting GuideTrouble Probable Cause Remedy Motor Repair Parts Parts List for Ridgid 6-1/8 Jointer/Planer Model No. JP06101Always order by Part Number Not by Key Number Description Key DescriptionRepair Parts Repair Parts Repair Parts Repair Parts Repair Parts JEG6 DAY Satisfaction Guarantee Policy Call
Top Page Image Contents