RIDGID JP06101 manual Mounting Jointer Table to Cabinet, Tensioning Belt and Installing Rear Panel

Page 15

Mounting Jointer Table to Cabinet

WARNING: This tool is heavy. To reduce the risk of back injury, get help whenever you have to lift the tool.

1.With help place the bed assembly upside down on two blocks as shown.

2.Place the jointer cabinet on top of the bed assembly as shown.

3.From the hardware pack find the following:

3 Serrated Hex Head Bolts 3/8-16 x 3/4" From among the loose parts find the following:

V-belt

4.Bolt the table to the cabinet using the 3 hex head bolts and tighten all three bolts. To access third bolt, reach into dust collection port on left side.

5.Slip the belt over both the motor and cutterhead pulleys.

Tensioning Belt and Installing Rear Panel

1.While the jointer is still upside down slide the motor up the motor mount to put tension on the belt. This will require assistance. Once the belt has been tensioned tighten the motor bolts. The belt should have approxi- mately 1" deflection (the measurement of how much you can push in on one side of the belt).

NOTE: An alternate method for tensioning the belt is to turn the unit upright, letting the motor slide down in the slots and allowing the weight of the motor only to tension the belt.

2.Visually check the front to back alignment of the pul- leys and adjust the motor as needed.

3.From the hardware pack locate the following:

6 Carriage Head Bolts 5/16-18 x 1/2"

6 Serrated Flange Hex Nuts 5/16"

From among the loose parts find the following: Rear Cabinet Panel

4.Position the rear panel in place from the bottom of the cabinet as shown. Bolt in place using the six 5/16 car- riage head bolts and six 5/16 flange nuts. Make sure the rear panel is on the inside of the cabinet side. Tighten the nuts.

5.Thread the power cord through the hole in the rear of the cabinet.

Carriage Head Bolt 5/16-18 x 1/2"

Rear Panel

Serrated Flange

Hex Nut 5/16

6.Remove the screws and washers from the cable plate.

7.Thread the power cord through the hole from the inside of the cabinet until the cord plate reaches the cabinet.

8.Reinstall the washers and screws from the outside of the cabinet with the cord plate flush against the inside of cabinet. Retighten screws.

V-Belt

3/8-16 x 3/4" Serrated Hex Head Bolt

NOTE: Motor mount and motor removed for clarity

Align Belt

and Tighten

Motor Mount

Nuts

NOTE: Table and motor removed for clarity

15

Image 15

Contents 235$725·60$18$ Safety Instructions For Jointer/Planer Table of ContentsMajor Hazards Before Using the Jointer/PlanerSafety Labels and Indicators on the Jointer/Planer Inspect Your Workpiece Plan Ahead To Protect Your Eyes, Hands, Face and EarsDon’t Force Tool Whenever Jointer/Planer Is RunningBefore Leaving the Jointer/Planer Keep Children AwayMotor Specifications and Electrical Requirements Power Supply and Motor SpecificationsGlossary of Terms for Woodworking Prong Plug Properly Grounded Outlet Grounding General Electrical ConnectionsVolt, 60 Hz. Tool Information Changing Motor VoltageMotor Safety Protection Wire SizesExtension Gauge A.W.G Cord Length Unpacking and Checking Contents Loose Parts Loose Parts From Hardware Pack Hex NutHex Nut 16-18 Cabinet and Motor Mount Assembly AssemblyInstall the Leveling Feet Motor Assembly with SwitchMounting the Motor Align Belt Tighten Motor Mount Nuts Tensioning Belt and Installing Rear PanelMounting Jointer Table to Cabinet Belt20 x 5/8 Installing the Pulley GuardInstalling Handwheel Serr 3/16-24 x 3/8 Belt GuardOutfeed Socket Head Screw Extension even with Outfeed table Adjusting Table ExtensionAttach Sawdust Chute Tool Storage Sawdust Chute Screw Wing 1/4-20 x 1/2Fence Lock Knob Nut Washer 1/2 Actual Size Not Install Cutter Head GuardAssembly Fence Nut Mount Assemble Fence To BedPan Head Screw Knob Adjusting Guard SpringAdjusting the Leveling Feet Cutter Head Guard Functional CheckNameplate Model/Serial Fence Tilt Bevel Knob Getting to Know Your Jointer/PlanerFence Sliding Knob Depth of Cut HandwheelOn-Off Switch Alignments Cutter Knife Alignment/Adjustments11/16 Wide New Blade Second Cutting Ground Surface Edge Cutter Knife SharpeningOutfeed Table Too Low Result Outfeed Table AdjustmentChecking Outfeed Table Alignment Outfeed Table Too High ResultStop Screw Bar Adjusting Table GibsFence Tilt Use and Bevel Stop Adjustment Angle Gauge UseSafety Instructions for Basic Jointer/Planer Operation Before Each UseFence Slide Lock Knob Bevel Lock Handle Plan your work Always Use Push Blocks When Planing, Beveling Or ChamferingFeeding the Workpiece All Operations Push blocks and push sticksBefore Leaving the jointer/planer Inspect your workpieceFeeding the Workpiece Basic Jointer/Planer Cutting OperationsDepth of Cut Handwheel Operation Stop Pin OperationJointing Without Push Blocks PlaningJointing Beveling/ChamferingFace Rabbet End Edge Using the Hold-Down/Push-BlocksRabbeting Support Long WorkpiecesSliding Lock Knob Sliding Fence OperationLubrication Maintenance and LubricationWiring Diagram MaintenanceTroubleshooting Guide GeneralTrouble Probable Cause Remedy Motor Parts List for Ridgid 6-1/8 Jointer/Planer Model No. JP06101 Repair PartsKey Description Always order by Part Number Not by Key Number DescriptionRepair Parts Repair Parts Repair Parts Repair Parts Repair Parts JEG6 Call DAY Satisfaction Guarantee Policy