RIDGID JP06101 manual Repair Parts

Page 42

Repair Parts

Parts List for RIDGID 6-1/8" Jointer/Planer

Model No. JP06101

RIDGID parts are available on-line at www.ridgidparts.com

 

Figure 4

 

1

 

8

 

 

7

2

 

9

 

5

6

3

8

 

4

10

11

12

13

14

10

11

Always order by Part Number - Not by Key Number

Key

Part No.

Description

No.

 

 

 

 

 

 

 

 

1

824886

Screw 1/4-28 x 7mm

2

824885

Wedge

3

AC8600

† Blade

4

821030

Screw Flat Hd Hex Soc

 

 

M5 x 0.8-12

5

818654-7

Key

6

820722-5

Bearing

7

824881-1

Support Bearing

 

 

 

These parts are available where you purchased your jointer.

Key

Part No.

Description

No.

 

 

 

 

 

 

 

 

8

160033-1

* Soc Set Screw 1/4-20 x 3/8

9

824888

Pulley

10

818826-8

* Lockwasher M10

11

824890

Screw Hex 3/8-24 x 3-1/2

12

828399

Cutter head

13

820722-6

Bearing

14

824879-1

Support Bearing

 

 

 

42

Image 42
Contents 235$725·60$18$ Table of Contents Safety Instructions For Jointer/PlanerBefore Using the Jointer/Planer Major HazardsSafety Labels and Indicators on the Jointer/Planer Plan Ahead To Protect Your Eyes, Hands, Face and Ears Inspect Your WorkpieceKeep Children Away Whenever Jointer/Planer Is RunningBefore Leaving the Jointer/Planer Don’t Force ToolMotor Specifications and Electrical Requirements Power Supply and Motor SpecificationsGlossary of Terms for Woodworking Changing Motor Voltage General Electrical ConnectionsVolt, 60 Hz. Tool Information Prong Plug Properly Grounded Outlet GroundingMotor Safety Protection Wire SizesExtension Gauge A.W.G Cord Length Unpacking and Checking Contents Loose Parts Loose Parts From Hardware Pack Hex NutHex Nut 16-18 Assembly Cabinet and Motor Mount AssemblyInstall the Leveling Feet Motor Assembly with SwitchMounting the Motor Belt Tensioning Belt and Installing Rear PanelMounting Jointer Table to Cabinet Align Belt Tighten Motor Mount NutsSerr 3/16-24 x 3/8 Belt Guard Installing the Pulley GuardInstalling Handwheel 20 x 5/8Tool Storage Sawdust Chute Screw Wing 1/4-20 x 1/2 Adjusting Table ExtensionAttach Sawdust Chute Outfeed Socket Head Screw Extension even with Outfeed tableAssemble Fence To Bed Install Cutter Head GuardAssembly Fence Nut Mount Fence Lock Knob Nut Washer 1/2 Actual Size NotCutter Head Guard Functional Check Adjusting Guard SpringAdjusting the Leveling Feet Pan Head Screw KnobDepth of Cut Handwheel Getting to Know Your Jointer/PlanerFence Sliding Knob Nameplate Model/Serial Fence Tilt Bevel KnobOn-Off Switch Cutter Knife Alignment/Adjustments AlignmentsCutter Knife Sharpening 11/16 Wide New Blade Second Cutting Ground Surface EdgeOutfeed Table Too High Result Outfeed Table AdjustmentChecking Outfeed Table Alignment Outfeed Table Too Low ResultAngle Gauge Use Adjusting Table GibsFence Tilt Use and Bevel Stop Adjustment Stop Screw BarSafety Instructions for Basic Jointer/Planer Operation Before Each UseFence Slide Lock Knob Bevel Lock Handle Push blocks and push sticks Always Use Push Blocks When Planing, Beveling Or ChamferingFeeding the Workpiece All Operations Plan your workInspect your workpiece Before Leaving the jointer/planerStop Pin Operation Basic Jointer/Planer Cutting OperationsDepth of Cut Handwheel Operation Feeding the WorkpieceBeveling/Chamfering PlaningJointing Jointing Without Push BlocksSupport Long Workpieces Using the Hold-Down/Push-BlocksRabbeting Face Rabbet End EdgeSliding Fence Operation Sliding Lock KnobMaintenance Maintenance and LubricationWiring Diagram LubricationTroubleshooting Guide GeneralTrouble Probable Cause Remedy Motor Repair Parts Parts List for Ridgid 6-1/8 Jointer/Planer Model No. JP06101Always order by Part Number Not by Key Number Description Key DescriptionRepair Parts Repair Parts Repair Parts Repair Parts Repair Parts JEG6 DAY Satisfaction Guarantee Policy Call