RIDGID JP06101 manual Maintenance and Lubrication, Wiring Diagram

Page 33

Maintenance and Lubrication

Maintenance

Do not allow pitch to accumulate on the tables, the fence, the cutter guard, the cutterhead or the knives. Clean them with an appropriate solvent.

Apply a thin coat of paste type wax to the tables and the fence so that the wood slides easily while feeding. This also deters rusting.

Do not allow chips to accumulate on the underside of the jointer/planer.

If power cord is worn, cut, or damaged in any way, have it replaced immediately.

Disassembly of the motor should only be done by an Authorized Service Center. Disregarding this may void your tools warranty.

NOTE: The speed of this motor cannot be regulated or changed.

Motors used on woodworking tools are particularly sus- ceptible to the accumulation of sawdust and wood chips and should be blown out or “vacuumed” frequently to pre- vent interference with normal motor ventilation.

Lubrication

WARNING: Unplug the jointer/planer. Unit could start suddenly. You could be badly hurt.

The ball bearings in this machine are packed with grease at the factory. They required no further lubrication.

The following parts should be oiled occasionally with SAE No. 20 or No. 30 engine oil.

1.Dovetail spacer and dovetail slide.

2.Elevation screw (first clean if necessary).

Wiring Diagram

Motor Junction Box

Motor Junction Box

3

5

2

1 3 5

2 4 8

1

4

8

Wire

Black

Wire

White Black

Nut

White

Nut

Green

Green

120V

240V

Power

Power

Cord

Cord

120V Wiring

240V Wiring

33

Image 33

Contents 235$725·60$18$ Safety Instructions For Jointer/Planer Table of ContentsMajor Hazards Before Using the Jointer/PlanerSafety Labels and Indicators on the Jointer/Planer Inspect Your Workpiece Plan Ahead To Protect Your Eyes, Hands, Face and EarsBefore Leaving the Jointer/Planer Whenever Jointer/Planer Is RunningKeep Children Away Don’t Force ToolMotor Specifications and Electrical Requirements Power Supply and Motor SpecificationsGlossary of Terms for Woodworking Volt, 60 Hz. Tool Information General Electrical ConnectionsChanging Motor Voltage Prong Plug Properly Grounded Outlet GroundingMotor Safety Protection Wire SizesExtension Gauge A.W.G Cord Length Unpacking and Checking Contents Loose Parts Loose Parts From Hardware Pack Hex NutHex Nut 16-18 Cabinet and Motor Mount Assembly AssemblyInstall the Leveling Feet Motor Assembly with SwitchMounting the Motor Mounting Jointer Table to Cabinet Tensioning Belt and Installing Rear PanelBelt Align Belt Tighten Motor Mount NutsInstalling Handwheel Installing the Pulley GuardSerr 3/16-24 x 3/8 Belt Guard 20 x 5/8Attach Sawdust Chute Adjusting Table ExtensionTool Storage Sawdust Chute Screw Wing 1/4-20 x 1/2 Outfeed Socket Head Screw Extension even with Outfeed tableAssembly Fence Nut Mount Install Cutter Head GuardAssemble Fence To Bed Fence Lock Knob Nut Washer 1/2 Actual Size NotAdjusting the Leveling Feet Adjusting Guard SpringCutter Head Guard Functional Check Pan Head Screw KnobFence Sliding Knob Getting to Know Your Jointer/PlanerDepth of Cut Handwheel Nameplate Model/Serial Fence Tilt Bevel KnobOn-Off Switch Alignments Cutter Knife Alignment/Adjustments11/16 Wide New Blade Second Cutting Ground Surface Edge Cutter Knife SharpeningChecking Outfeed Table Alignment Outfeed Table AdjustmentOutfeed Table Too High Result Outfeed Table Too Low ResultFence Tilt Use and Bevel Stop Adjustment Adjusting Table GibsAngle Gauge Use Stop Screw BarSafety Instructions for Basic Jointer/Planer Operation Before Each UseFence Slide Lock Knob Bevel Lock Handle Feeding the Workpiece All Operations Always Use Push Blocks When Planing, Beveling Or ChamferingPush blocks and push sticks Plan your workBefore Leaving the jointer/planer Inspect your workpieceDepth of Cut Handwheel Operation Basic Jointer/Planer Cutting OperationsStop Pin Operation Feeding the WorkpieceJointing PlaningBeveling/Chamfering Jointing Without Push BlocksRabbeting Using the Hold-Down/Push-BlocksSupport Long Workpieces Face Rabbet End EdgeSliding Lock Knob Sliding Fence OperationWiring Diagram Maintenance and LubricationMaintenance LubricationTroubleshooting Guide GeneralTrouble Probable Cause Remedy Motor Parts List for Ridgid 6-1/8 Jointer/Planer Model No. JP06101 Repair PartsKey Description Always order by Part Number Not by Key Number DescriptionRepair Parts Repair Parts Repair Parts Repair Parts Repair Parts JEG6 Call DAY Satisfaction Guarantee Policy