Miller Electric and SS-75D16 manual Installing Wire Guide Extension, Equipment Connection Diagram

Page 15

4-4. Installing Wire Guide Extension

1		1	Wire Guide Fitting
		2	Bolt

	4	3	Monocoil Liner
		4	Wire Guide Extension

2 3		Tighten bolt to secure liner in wire
		guide fitting. Do not overtighten bolt

and crush liner.

Tools Needed:

3/8 in

ST-152 323

4-5. Equipment Connection Diagram

1

2

3

4

5

6

7

10

YTurn Off wire feeder and welding power source. Stop engine on welding generator.

YUse only with CC/CV DC

13	Power Sources.

1Constant Current (CC) or Constant Voltage (CV) Welding Power Supply

2Remote 14 Connection

3Weld Cable To Feeder

4Ground Cable To Workpiece

	12	Weld cable and ground cable con-
	12	nections to power source (DCEN/
		nections to power source (DCEN/
		DCEP) are dependant on wire type.
		5	Workpiece
		6	Weld Control
		7	Boom
		8	Gun
		9	Trigger Connection
		10	Swivel
		11	Pipe Post And Base
		12	Gas Hose
		13	Gas Supply And Regulator
			(Customer Supplied)

	. Shielding gas pressure not to
11	exceed 100 PSI (689 kPa).
11

8

9

804 726-A

OM-230 298 Page 11

Image 15

Contents File MIG Gmaw OM-230 298AProcesses DescriptionFrom Miller to You Table of Contents Page Electric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesCalifornia Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Pacemakers UNE Décharge Électrique peut entraîner la mort LES Fumées ET LES GAZ peuvent être dangereuxIndique un message de sécurité particulier DES Pièces Chaudes peuvent provoquer des brûlures graves LE Soudage peut provoquer unIncendie ou une explosion DES Particules Volantes peuvent blesser les yeuxDES Organes Mobiles peuvent provoquer des blessures Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peut SUREn ce qui concerne les stimulateurs cardiaques Principales normes de sécurité− Introduction − InstallationSpecifications Installing Swivel Into Pipe PostInstalling Boom And Reel Support Adjusting Control Tilt BracketEquipment Connection Diagram Installing Wire Guide ExtensionControl Box Connections Pin Plug InformationPin Information Gun Recommendation Table Removing Safety Collar And Adjusting BoomWire Type, Size, And Feed Speed Capability Table Motor Speed Wire Type Wire Size Feed Speed CapabilityInstalling Drive Rolls InstallationRemoval Installing PD continuous wire guides with PD drive rolls Installing PD Continuous Wire GuidesInstalling wire guides with non- PD old- style drive rolls Installing Non-PD Old Style Wire GuidesInstalling gun with Accu-Mate connec- tion Installing Welding GunInstalling gun with Accu-Mate connection Installing gun without Accu-Mate connectionInstalling Welding Wire And Adjusting Pressure Drive Setting S1-1 And S1-2 Setting Internal DIP SwitchesRun-In Disabled S1-1 Manually Adjusted Run-In S1-1 And S1-2− Operation Equipment DIP Switch Settings For Models With Meters OnlyDigital Meter DIP Switch Setting General Terms Cold Wire JogJog/Purge And Trigger Hold Power SwitchYou can adjust the preset volt Disconnect power before maintaining − Maintenance and TroubleshootingRoutine Maintenance Brush Inspection And ReplacementDiagnostics Indicated ErrorError Indications Troubleshooting Disconnect power before troubleshootingTrouble Remedy Circuit Diagram − Electrical DiagramStart Your Professional Welding Career Now Main Assembly − Parts ListQuantity Control Box 070 Boom Assembly Boom Assembly -1Item Drive Assembly, Wire Drive Assembly With Motor Support, Hub & Reel PD-V OM-230 298 Support ServiceMiller Electric Mfg. Co Owner’s Record