Miller Electric SS-75S16, SS-75S12 Control Box Connections, Pin Plug Information, Pin Information

Page 16

4-6. Control Box Connections

1 Interconnecting Cable

Receptacle

2 Interconnecting Cable

3 14-Pin Control Cable

2

3

1

Ref. 803 019

4-7. 14-Pin Plug Information

 

 

 

Pin*

Pin Information

 

 

 

A

24 volts ac with respect to socket G.

 

 

 

B

Contact closure to A completes 24 volts ac contactor control circuit.

I J

 

A

G

Circuit common for 24 volts ac circuit.

K

 

 

 

 

B

C

+10 volts dc output to remote control with respect to socket D.

 

 

L C

H

N

D

Remote control circuit common.

G

M

D

 

 

F

E

 

E

0 to +10 volts dc input command signal from remote control with respect to socket D.

 

 

 

H

Voltage feedback; 0 to +10 volts dc, 1 volt per 10 arc volts.

 

 

 

F

Current feedback; 0 to +10 volts dc, 1 volt per 100 amperes.

*The remaining pins are not used.

OM-230 298 Page 12

Image 16
Contents OM-230 298A ProcessesDescription File MIG GmawFrom Miller to You Table of Contents Page Symbol Usage Marks a special safety messageArc Welding Hazards Electric Shock can killARC Rays can burn eyes and skin Welding can cause fire or explosionFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers LES Fumées ET LES GAZ peuvent être dangereux UNE Décharge Électrique peut entraîner la mortIndique un message de sécurité particulier LE Soudage peut provoquer un Incendie ou une explosionDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures gravesRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesser’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sécurité En ce qui concerne les stimulateurs cardiaques− Installation SpecificationsInstalling Swivel Into Pipe Post − IntroductionAdjusting Control Tilt Bracket Installing Boom And Reel SupportInstalling Wire Guide Extension Equipment Connection DiagramPin Plug Information Control Box ConnectionsPin Information Removing Safety Collar And Adjusting Boom Wire Type, Size, And Feed Speed Capability TableMotor Speed Wire Type Wire Size Feed Speed Capability Gun Recommendation TableInstallation Installing Drive RollsRemoval Installing PD Continuous Wire Guides Installing PD continuous wire guides with PD drive rollsInstalling Non-PD Old Style Wire Guides Installing wire guides with non- PD old- style drive rollsInstalling Welding Gun Installing gun with Accu-Mate connectionInstalling gun without Accu-Mate connection Installing gun with Accu-Mate connec- tionInstalling Welding Wire And Adjusting Pressure Drive Setting Setting Internal DIP Switches Run-In Disabled S1-1Manually Adjusted Run-In S1-1 And S1-2 S1-1 And S1-2Equipment DIP Switch Settings For Models With Meters Only Digital Meter DIP Switch SettingGeneral Terms Cold Wire Jog − OperationPower Switch Jog/Purge And Trigger HoldYou can adjust the preset volt − Maintenance and Troubleshooting Routine MaintenanceBrush Inspection And Replacement Disconnect power before maintainingIndicated Error DiagnosticsError Indications Disconnect power before troubleshooting TroubleshootingTrouble Remedy − Electrical Diagram Circuit DiagramStart Your Professional Welding Career Now − Parts List Main AssemblyQuantity Control Box 070 Boom Assembly Boom Assembly -1Item Drive Assembly, Wire Drive Assembly With Motor Support, Hub & Reel PD-V OM-230 298 Service SupportOwner’s Record Miller Electric Mfg. Co